The current value can be displayed on the operation panel without regard to the setting of monitor-related parameters. A

The English version cannot be updated from the Website. FR-SW3-SETUP-WE needs to be purchased.

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit.

1. As the measurement condition is unknown, the possible cases are as follows: - If you measured the current on the inp

The 0.75 kW inverter with the single-phase 100 V power supply can be manufactured and is actually commercialized as the

It is the same as the one by the inverter whose capacity is one-rank higher than the FR-A500L series.

The acceleration time is 60 Hz and 5 seconds, and deceleration time is 60 Hz and 60 seconds.

No error will occur because up to 400 Hz that is the upper limit of the setting range can be written.

The wound rotor motor can be used in the same way as cage-induction motors by shortening the resistor at the secondary s

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1-10 of Total 1368

prev 1 / 137page next

Current value monitor

The current value can be displayed on the operation panel without regard to the setting of monitor-related parameters. As the current value remains 0 A, the ... More Details >>
- No：21405
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Stop-on-contact control

Yes. More Details >>
- No：21041
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR Configurator (English version)

The English version cannot be updated from the Website. FR-SW3-SETUP-WE needs to be purchased. More Details >>
- No：21195
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Torque limit

There is no setting to disable it, but setting a high torque limit level such as 400 % can disable the limit. More Details >>
- No：21217
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Inverter current value

1. As the measurement condition is unknown, the possible cases are as follows: - If you measured the current on the input side of the inverter, since the cu... More Details >>
- No：21457
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Single-phase 100 V series

The 0.75 kW inverter with the single-phase 100 V power supply can be manufactured and is actually commercialized as the FR-U100 series. Manufacturing of the ... More Details >>
- No：21509
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Amount of heat generated by the FR-V500L

It is the same as the one by the inverter whose capacity is one-rank higher than the FR-A500L series. More Details >>
- No：20854
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR-FS

The acceleration time is 60 Hz and 5 seconds, and deceleration time is 60 Hz and 60 seconds. More Details >>
- No：21166
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Writing set frequency by CC-Link communication

No error will occur because up to 400 Hz that is the upper limit of the setting range can be written. More Details >>
- No：21229
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Issues of driving the wound rotor motor inverter

The wound rotor motor can be used in the same way as cage-induction motors by shortening the resistor at the secondary side. More Details >>
- No：21370
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL

1-10 of Total 1368

Inquiries

page top