You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch whil

It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting

It is approximately 500,000 times in the rated specification.

Configure the same setting as the SF-HRCA. Configure the same setting as the SF-HRCA. A700, E700, D700, F700PJ: Pr.71 =

If using an inverter with capacity of 75K or higher, or motor with capacity of 75 kW or higher, always select and instal

When the MR-J4-B is selected on the model selection screen at creating a new project, the multi-axis check box will be e

The pulse train form outputted with the controller and the setting of servo amplifier (command pulse input form) may dif

Yes, it is. For MR-J4-A/MR-J3-A, set by [Pr. PC13]. As the initial value (100.0%), the maximum torque is generated at ±

You can switch between the NET mode and external operation.Assign the X66 signal (Operation switching) to an unused term

No. This is because the current cannot flow if the total internal impedance of the meter connected to the terminal FM is

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

91-100 of Total 1368

prev 10 / 137page next

Switching between external operation and NET operation

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch while Pr.79 (Operation mode) is set to "6... More Details >>
- No：21688
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Replacement

It is Pr.125 (Terminal 2 frequency setting gain frequency). Adjust the slope with C4 (903) (Terminal 2 frequency setting gain) as necessary. More Details >>
- No：21247
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
ABC terminal

It is approximately 500,000 times in the rated specification. More Details >>
- No：21202
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Motor: SF-HJCA

Configure the same setting as the SF-HRCA. Configure the same setting as the SF-HRCA. A700, E700, D700, F700PJ: Pr.71 = 50F700P, F700: Pr.71 = 1 (Reference) ... More Details >>
- No：21136
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , Peripheral devices , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
DC reactor

If using an inverter with capacity of 75K or higher, or motor with capacity of 75 kW or higher, always select and install the inverter based on the capacity ... More Details >>
- No：21112
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , Options , FREQROL-F800
Specifying the axis in test operation of MR-J4W

When the MR-J4-B is selected on the model selection screen at creating a new project, the multi-axis check box will be enabled. Click the check box and selec... More Details >>
- No：23635
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4 , MELSERVO-J3
Servo motor does not rotate when the command pulse is input.

The pulse train form outputted with the controller and the setting of servo amplifier (command pulse input form) may differ. Check the parameter settings. (M... More Details >>
- No：23631
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE , MELSERVO-JN , MELSERVO-J3 , MELSERVO Others
Changing multiplication of analog torque command

Yes, it is. For MR-J4-A/MR-J3-A, set by [Pr. PC13]. As the initial value (100.0%), the maximum torque is generated at ±8 V. To generate the maximum torque a... More Details >>
- No：23628
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE , MELSERVO-J3 , MELSERVO Others
NET mode, external operation switching

You can switch between the NET mode and external operation.Assign the X66 signal (Operation switching) to an unused terminal for switching.Also, set Pr.79 (O... More Details >>
- No：21906
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Terminal FM

No. This is because the current cannot flow if the total internal impedance of the meter connected to the terminal FM is 300 Ω or higher.You can connect mult... More Details >>
- No：21864
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

91-100 of Total 1368

Inquiries

page top