When the DIP switch is changed to I, it does not operate normally because the internal resistance changes.

Inverters with the components fixed on the circuit board with an adhesive, an countermeasure against the connector faili

By inputting the rope length, the speed command is sent to suppress a swinging.

FR-FS-0.4K: 35 W, FR-FS-0.8K: 65 W, Noise filter: 4 W

Setting of Pr.408 (Thermistor selection) is required. Set as follows. For the model of SF-V5RU ending with "T" (SF-V5RU○

Refer to the inverter capacity.

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur wh

When performing the PID control by CC-Link communication, the X14 signal is disabled.

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises

No, it is not changed. Pr.268 is the parameter for the operation panel.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

91-100 of Total 1353

prev 10 / 136page next

Terminal 2 input selector switch when the PTC thermistor is connected

When the DIP switch is changed to I, it does not operate normally because the internal resistance changes. More Details >>
- No：20901
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR-A800-CRN

Inverters with the components fixed on the circuit board with an adhesive, an countermeasure against the connector failing, or the cables tied (fixed) togeth... More Details >>
- No：20931
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-A800-CRN

By inputting the rope length, the speed command is sent to suppress a swinging. More Details >>
- No：20935
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-FS

FR-FS-0.4K: 35 W, FR-FS-0.8K: 65 W, Noise filter: 4 W More Details >>
- No：21165
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Setting when using the FR-A7AZ and SF-V5RU

Setting of Pr.408 (Thermistor selection) is required. Set as follows. For the model of SF-V5RU ending with "T" (SF-V5RU○○T): Pr.408 = 0 For the model of SF-V... More Details >>
- No：21169
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Wiring length

Refer to the inverter capacity. More Details >>
- No：21200
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
IPM motor drive

Overshooting of the speed due to the acceleration/deceleration may be the cause. Overshooting is more likely to occur when the load inertia is too high. As a... More Details >>
- No：21216
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
PID control of CC-Link communication

When performing the PID control by CC-Link communication, the X14 signal is disabled. More Details >>
- No：21233
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Earthing (grounding) of FR-A7NC (E kit)

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises. More Details >>
- No：21240
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Pr.268 (Monitor decimal digits selection) during CC-Link communication

No, it is not changed. Pr.268 is the parameter for the operation panel. More Details >>
- No：21241
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

91-100 of Total 1353

Inquiries

page top