1. Torque control automatically adjust the speed so that the instructed torque value is maintained. This means that the

It is considered to be caused by inverter PWM control. It can be suppressed by raising the PWM carrier frequency (Pr.72)

You can switch between PU operation and external operation using the plug-in option "12-bit digital input" card and exte

Check if Pr.13 (Starting frequency) is set to higher than 10 Hz.Also check if a signal is input through the terminal MRS

Change the setting in the PU operation mode.

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with

Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4".

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intende

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1001-1010 of Total 1353

prev 101 / 136page next

Unwinding using vector inverter

1. Torque control automatically adjust the speed so that the instructed torque value is maintained. This means that the speed is not controlled. (However, yo... More Details >>
- No：21420
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Noise from motor at low speed

It is considered to be caused by inverter PWM control. It can be suppressed by raising the PWM carrier frequency (Pr.72), but the entire noise and leakage cu... More Details >>
- No：21428
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
12-bit digital input and others

You can switch between PU operation and external operation using the plug-in option "12-bit digital input" card and external contact signals. After setting P... More Details >>
- No：21432
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A200
Parameter setting

Check if Pr.13 (Starting frequency) is set to higher than 10 Hz.Also check if a signal is input through the terminal MRS. More Details >>
- No：21722
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
CC-Link station number setting

Change the setting in the PU operation mode.　　 More Details >>
- No：21747
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Minimum frequency

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with Pr.13 (Starting frequency) up to 3 H... More Details >>
- No：21777
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).　　 More Details >>
- No：21792
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4". More Details >>
- No：21839
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Brake unit selection

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply voltage 480 V- What resistance value... More Details >>
- No：21930
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Motor retention at 0 Hz

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intended to improve the braking capability b... More Details >>
- No：22002
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500

1001-1010 of Total 1353

Inquiries

page top