Create a ladder program to read inverter faults on the programmable controller.Set the instruction code (H74-H77) and tu

You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting t

You can set reserved and invalid stations.The Instruction Manual instructs to set consecutive numbers because the master

Refer to the Technical Sheet No.23 (Capacity Selection and Continuous Operation) for reference for selection. Optional c

Some parameters are write-protected. (MR-J4/MR-J3: PA19)The parameter to be displayed is determined by the setting value

Since the SF-PR is more efficient compared to the SF-JR, the resistance will decrease and the load current will increase

When the winding ratio is large, the control according to the winding diameter is required. The upper controller has mea

It can be used in terms of the specifications. However, it is recommended to update the reactor and inverter at the same

No. They can be connected with the connection cable (FR-CB20[]). [] indicates cable length (1 m, 3 m, 5 m).

Approximately 2 years when the FR-LU08 is not energized and the real-time clock function is enabled.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1011-1020 of Total 1368

prev 102 / 137page next

CC-Link

Create a ladder program to read inverter faults on the programmable controller.Set the instruction code (H74-H77) and turn ON the instruction code execution ... More Details >>
- No：21886
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting to stop, deceleration to stop, and con... More Details >>
- No：21892
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

You can set reserved and invalid stations.The Instruction Manual instructs to set consecutive numbers because the master regards an empty number as an error. More Details >>
- No：21905
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Calculation of inverter acceleration and deceleration time

Refer to the Technical Sheet No.23 (Capacity Selection and Continuous Operation) for reference for selection. Optional capacity selection software is also pr... More Details >>
- No：22097
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Parameter group is not displayed.

Some parameters are write-protected. (MR-J4/MR-J3: PA19)The parameter to be displayed is determined by the setting value of this parameter. Do as follows for... More Details >>
- No：23657
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J3 , MELSERVO-J4
Replacement of the SF-JR with the SF-PR

Since the SF-PR is more efficient compared to the SF-JR, the resistance will decrease and the load current will increase. Check the following two points when... More Details >>
- No：20949
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Others
FR-A800-R2R

When the winding ratio is large, the control according to the winding diameter is required. The upper controller has measured the winding diameter and create... More Details >>
- No：20974
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
Use of the DC reactor

It can be used in terms of the specifications. However, it is recommended to update the reactor and inverter at the same time because the DC reactor was manu... More Details >>
- No：21017
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , Inverters-FREQROL , FREQROL-F800 , FREQROL-A500 , FREQROL-F500
FR-PU07

No. They can be connected with the connection cable (FR-CB20[]). [] indicates cable length (1 m, 3 m, 5 m). More Details >>
- No：21081
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800 , FREQROL-F800
FR-LU08

Approximately 2 years when the FR-LU08 is not energized and the real-time clock function is enabled. More Details >>
- No：21084
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options , FREQROL-A800 , FREQROL-F800

1011-1020 of Total 1368

Inquiries

page top