The machine analyzer analyzes the machine frequency characteristic and calculates the frequency of machine resonance su

You can solder the wiring to the connector without using the junction terminal block (option).

As you mention, when the inverter is operated only with STF without inputting the speed command signal, the minimum freq

Just by adding this option, encoder pulses connected to the inverter or option are output.You can also divide the pulse

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the ou

If you ground the common terminals of the control circuit, it is connected with the inverter's earthing and the inverter

The brake unit and its resistor FR-S520-0.4K to 3.7K are available.Mitsubishi Electric FA Global Website also explains s

The rotation ripple data for 1.5 kW is shown below.Drive unit: MD-CX520-1.5KMotor: MM-CF152Load: None (motor alone), car

The fault output terminals A and C, and B and C of the power regeneration converter FR-RC are not capable of a micro loa

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1011-1020 of Total 1354

prev 102 / 136page next

Machine analyzer

The machine analyzer analyzes the machine frequency characteristic and calculates the frequency of machine resonance suppression filter by measuring the res... More Details >>
- No：23656
- Release Date：2018/09/14 15:10
- Category： Servo Support Software
Wiring to connector

You can solder the wiring to the connector without using the junction terminal block (option). More Details >>
- No：23654
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4
Switching between high speed and low speed

As you mention, when the inverter is operated only with STF without inputting the speed command signal, the minimum frequency must be set to 10 Hz.However, a... More Details >>
- No：22078
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Vector inverter option

Just by adding this option, encoder pulses connected to the inverter or option are output.You can also divide the pulse train output. More Details >>
- No：22062
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Pulse train output of terminal FM

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the output frequency monitor value to chang... More Details >>
- No：22054
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Common terminals of control circuit

If you ground the common terminals of the control circuit, it is connected with the inverter's earthing and the inverter's noise may be input to the control ... More Details >>
- No：22037
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Can I use a brake resistor with the FR-S500?

The brake unit and its resistor FR-S520-0.4K to 3.7K are available.Mitsubishi Electric FA Global Website also explains so.(Note that the GZG GRZG discharging... More Details >>
- No：21970
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
Rotation ripple at low speed

The rotation ripple data for 1.5 kW is shown below.Drive unit: MD-CX520-1.5KMotor: MM-CF152Load: None (motor alone), carrier frequency: 2 kHz, wiring length:... More Details >>
- No：21968
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
Fault output terminal load pattern

The fault output terminals A and C, and B and C of the power regeneration converter FR-RC are not capable of a micro load of 5 VDC±5%, 10 mA. The minimum loa... More Details >>
- No：21966
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Brake unit selection

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply voltage 480 V- What resistance value... More Details >>
- No：21930
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options

1011-1020 of Total 1354

Inquiries

page top