The frequency setting in the communication cannot be used together with FR-A8AX. The priority of the FR-A8AX is equal to

Up to 20 pieces of sampling data can be saved. The oldest data is overwritten when more than 20 pieces of data are to be

The number of terminals: There are the same output terminals as F700P and the following terminals (2 points) are added.

Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during

Basically, torque control cannot be performed. Instead, control speed to adjust the winding torque. It is possible to us

The inverter (FR-A520-5.5K) itself generates approximately 310 W of heat. This is the amount generated under the inverte

The rated sensitivity current of the earth leakage circuit breaker can be calculated using the following equation. If th

Yes, you can set Pr.20 to 20 Hz.

The FREQROL-F500 series has been already supported by the setup software released since February 2000.

Position control is available under vector control with an encoder. Under PM sensorless vector control in combination wi

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1021-1030 of Total 1353

prev 103 / 136page next

FR-A8NC/FR-A8AX

The frequency setting in the communication cannot be used together with FR-A8AX. The priority of the FR-A8AX is equal to the second terminal analog input and... More Details >>
- No：20917
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Plug-in Options
FR Configurator2

Up to 20 pieces of sampling data can be saved. The oldest data is overwritten when more than 20 pieces of data are to be saved. More Details >>
- No：20991
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Engineering Software
The number of output terminals

The number of terminals: There are the same output terminals as F700P and the following terminals (2 points) are added. Safety: SO, SOC *The terminals SO and... More Details >>
- No：21069
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-F800
Switching External operation, PU operation

Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during External operation switches the mode ... More Details >>
- No：21289
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Simple torque control using stall prevention function

Basically, torque control cannot be performed. Instead, control speed to adjust the winding torque. It is possible to use the current limit function to preve... More Details >>
- No：21493
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Amount of heat

The inverter (FR-A520-5.5K) itself generates approximately 310 W of heat. This is the amount generated under the inverter rated current 100% load. Since the ... More Details >>
- No：21523
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Sensitivity current of earth leakage circuit breaker

The rated sensitivity current of the earth leakage circuit breaker can be calculated using the following equation. If the result is 30 mA or less, the NV-FA ... More Details >>
- No：21547
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Peripheral devices
Frequency setting

Yes, you can set Pr.20 to 20 Hz. More Details >>
- No：21683
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Can I set the FR-F series parameters?

The FREQROL-F500 series has been already supported by the setup software released since February 2000. More Details >>
- No：22068
- Release Date：2018/08/22 16:30
- Category： Engineering Software
FR-A800

Position control is available under vector control with an encoder. Under PM sensorless vector control in combination with a MM-CF motor, simple positioning ... More Details >>
- No：21105
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800

1021-1030 of Total 1353

Inquiries

page top