Set the rated frequency of the motor used to it.

The following causes are probable for this Err display:- Operation error (for example, you tried to input a value other

The performance and noise countermeasure were improved and the initial value is set to "8". Try with the initial value "

Turning ON the main circuit power stops the 24 V external power supply operation and enables the normal operation. There

Ver1.1 (Ver2.0 (full speed) compatible). USB1.1 supports Full Speed (12 Mbps) and Low Speed (1.5 Mbps) transmission spee

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (

Increasing the value of Pr.0 (Torque boost) increases the output voltage, and the output current also increases.Note tha

If "1" is not shown on the frequency monitor, some of the parameters necessary for auto tuning may not be set correctly.

This subroutine is to check the data link status and needs to be executed only once at the start of the program.

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1031-1040 of Total 1353

prev 104 / 136page next

Base frequency setting value

Set the rated frequency of the motor used to it.　 More Details >>
- No：21814
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Err display on operation panel

The following causes are probable for this Err display:- Operation error (for example, you tried to input a value other than the available range of parameter... More Details >>
- No：22063
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Setting values of the FR-F800 when replaced with the FR-F400

The performance and noise countermeasure were improved and the initial value is set to "8". Try with the initial value "2" first. If the noise is distracting... More Details >>
- No：20808
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800
Control power supply

Turning ON the main circuit power stops the 24 V external power supply operation and enables the normal operation. Therefore, the separate power supply canno... More Details >>
- No：21018
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
USB version

Ver1.1 (Ver2.0 (full speed) compatible). USB1.1 supports Full Speed (12 Mbps) and Low Speed (1.5 Mbps) transmission speed modes. USB2.0 supports High Speed (... More Details >>
- No：21096
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
Difference between SU (up to frequency) and FU (frequency detection)

- SU signal (up to frequency signal)This signal is output when the inverter output frequency reaches the set frequency (the frequency the inverter is require... More Details >>
- No：21436
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Output current

Increasing the value of Pr.0 (Torque boost) increases the output voltage, and the output current also increases.Note that increasing this value too high puts... More Details >>
- No：21732
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Auto tuning

If "1" is not shown on the frequency monitor, some of the parameters necessary for auto tuning may not be set correctly.Set rated motor current of Pr.81 (Num... More Details >>
- No：21751
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Program command

This subroutine is to check the data link status and needs to be executed only once at the start of the program. More Details >>
- No：21767
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).　　 More Details >>
- No：21802
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

1031-1040 of Total 1353

Inquiries

page top