Since the inverter power supply uses the single-phase input, you cannot use a 0.75K inverter with a 0.6 kW motor to draw

Basically, there is no difference between the A200 and A500. For safer use, from the A500, it is recommended to complete

1. You can set the minimum time by setting the acceleration/deceleration time and acceleration/deceleration reference fr

An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the ma

After inputting the start signal performing the tuning, output the output frequency. The tuning ends in approximately 5

Keep a clearance of "minimum 10cm each on top and bottom and minimum 5cm each on right and left".

The following reasons are possible. - The signal of Z phase does not exist. (It is not returned normally.) - The setting

The operation panel is also compatible with the IP55

No, the update cycle is not changed.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1051-1060 of Total 1353

prev 106 / 136page next

Using dedicated motor

Since the inverter power supply uses the single-phase input, you cannot use a 0.75K inverter with a 0.6 kW motor to draw the maximum ability of the motor. To... More Details >>
- No：21470
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A024
Installing magnetic contactor on input side of inverter

Basically, there is no difference between the A200 and A500. For safer use, from the A500, it is recommended to completely shut off the power supply by turni... More Details >>
- No：21466
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Durability in multi-speed setting

1. You can set the minimum time by setting the acceleration/deceleration time and acceleration/deceleration reference frequency. 2. No problem with the termi... More Details >>
- No：21437
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Detection of the motor load

An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the magnitude of the load will change when ... More Details >>
- No：21387
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Magnetic flux and tuning

After inputting the start signal performing the tuning, output the output frequency. 　The tuning ends in approximately 500 ms in maximum after started. Durin... More Details >>
- No：21372
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-CVL

Keep a clearance of "minimum 10cm each on top and bottom and minimum 5cm each on right and left". More Details >>
- No：21178
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
Orientation control

The following reasons are possible. - The signal of Z phase does not exist. (It is not returned normally.) - The setting of Pr.359 encoder rotation direction... More Details >>
- No：21162
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
FR-A800

The operation panel is also compatible with the IP55 More Details >>
- No：21091
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800
Torque monitoring

No, the update cycle is not changed. More Details >>
- No：21044
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL

1051-1060 of Total 1353

Inquiries

page top