Using MR Configurator2, you can perform the positioning operation when there is no command from the controller. You can

The inverter itself does not have a function to detect the rotation angle and change the velocity accordingly. Therefore

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the fol

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of

When the wiring between the inverter and motor is long, surge voltage occurs at the terminal of the motor.This surge vol

Noise filtering and harmonics suppression are different matters and you need to install the line noise filter (FR-BSF01)

The rated sensitivity current of the earth leakage circuit breaker can be calculated using the following equation. If th

Possible causes are:1. The reset signal (RES) is ON. 2. The built-in CPU is not working properly due to contact faults o

Leave the setting of Pr.96 as "3". It indicates that auto tuning has been completed and the motor constant has been read

When FR Configurator (FR-SW3-SETUP-WJ) is saved as a file from the menu, the extension is "me3". The size of this fie wi

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

101-110 of Total 1368

prev 11 / 137page next

Positioning operation

Using MR Configurator2, you can perform the positioning operation when there is no command from the controller. You can perform the operation specifying the ... More Details >>
- No：23640
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4 , MELSERVO-JE , MELSERVO-JN , MELSERVO-J3
Angular velocity change control

The inverter itself does not have a function to detect the rotation angle and change the velocity accordingly. Therefore, to implement required control, it i... More Details >>
- No：22086
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-V200
Changing main speed at analog signal input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the following steps:1. Change Pr.77 to "2".2... More Details >>
- No：22025
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Alarm output signal when using CC-Link

The RX7 output signal is the same as the signals for NO, NC, and transfer contact output.You can change the contents of this output signal using Pr.192.Pr.19... More Details >>
- No：22008
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Inverter drive of 400 V class motor

When the wiring between the inverter and motor is long, surge voltage occurs at the terminal of the motor.This surge voltage deteriorates insulation of the m... More Details >>
- No：21926
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-B , FREQROL-A500 , FREQROL-F500 , FREQROL-A024 , FREQROL-E500 , FREQROL-V200 , FREQROL-A200 , FREQROL-S500 , FREQROL-A100
Noise filter

Noise filtering and harmonics suppression are different matters and you need to install the line noise filter (FR-BSF01) against noise and DCL (FR-BEL) again... More Details >>
- No：21548
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Sensitivity current of earth leakage circuit breaker

The rated sensitivity current of the earth leakage circuit breaker can be calculated using the following equation. If the result is 30 mA or less, the NV-FA ... More Details >>
- No：21547
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Peripheral devices
"Err" is displayed when STF signal turns ON

Possible causes are:1. The reset signal (RES) is ON. 2. The built-in CPU is not working properly due to contact faults of the inverter parts. Check the exte... More Details >>
- No：21484
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Offline auto tuning

Leave the setting of Pr.96 as "3". It indicates that auto tuning has been completed and the motor constant has been read. When it is changed unnecessarily, t... More Details >>
- No：21352
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Saving parameter with FR-Configurator

When FR Configurator (FR-SW3-SETUP-WJ) is saved as a file from the menu, the extension is "me3". The size of this fie will be large since device settings and... More Details >>
- No：21311
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

101-110 of Total 1368

Inquiries

page top