Pr.133 can be written.Since the data code numbers of parameters are duplicate, target parameters are switched by link pa

The inverter overcurrent shut-off fault indication E.OC1, E.OC2, or E.OC3 is not only displayed when the inverter output

It cannot be connected. When using DU08, connect it to the PU connector.

The value is displayed in 0.1 rpm increments under Vector control. However, the value is rounded down to the first decim

A tension sensor such as a dancer roll is required for speed control. Because an actual line speed input is required for

Almost same control method. This control also performs vector calculation and divides the inverter's output current into

For tuning of a single motor with no load, set Pr.96 to "101". When a load is connected, set Pr.96 to "1" (without motor

The number of timer points is 16 for the high speed and low speed in total.

Yes. the options support it. By connecting the following communication option (built-in circuit board) manufactured and

The power running is the status that the servo amplifier is supplying the power to the servo motor when the servo motor

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

101-110 of Total 1353

prev 11 / 136page next

Parameter writing via CC-Link

Pr.133 can be written.Since the data code numbers of parameters are duplicate, target parameters are switched by link parameter extended setting.You can acce... More Details >>
- No：21976
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500 , FREQROL-F500
Error

The inverter overcurrent shut-off fault indication E.OC1, E.OC2, or E.OC3 is not only displayed when the inverter output current reaches approximately 200% o... More Details >>
- No：21519
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A200
FR-DU08

It cannot be connected. When using DU08, connect it to the PU connector. More Details >>
- No：21111
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
Frequency setting increment

The value is displayed in 0.1 rpm increments under Vector control. However, the value is rounded down to the first decimal place and displayed in 1 rpm incre... More Details >>
- No：21021
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800
FR-A800-R2R

A tension sensor such as a dancer roll is required for speed control. Because an actual line speed input is required for the winding diameter calculation by ... More Details >>
- No：20926
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
General-purpose magnetic flux control

Almost same control method. This control also performs vector calculation and divides the inverter's output current into an excitation current and into a tor... More Details >>
- No：21620
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Real sensorless vector control

For tuning of a single motor with no load, set Pr.96 to "101". When a load is connected, set Pr.96 to "1" (without motor rotation). Since Real sensorless vec... More Details >>
- No：21325
- Release Date：2018/08/22 16:27
- Category： FREQROL-A700
PLC function

The number of timer points is 16 for the high speed and low speed in total. More Details >>
- No：21056
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
FR-A800 and Ethernet IP communication

Yes. the options support it. By connecting the following communication option (built-in circuit board) manufactured and sold by HMS to the FR-A800 series, th... More Details >>
- No：20823
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A800
What are power running and regeneration?

The power running is the status that the servo amplifier is supplying the power to the servo motor when the servo motor drives the load. (Example) When the s... More Details >>
- No：23626
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE , MELSERVO-JN , MELSERVO-J3 , MELSERVO Others

101-110 of Total 1353

Inquiries

page top