The output signal across FM and SD is pulse output. The output frequency and number of pulses of the output signal acros

Speed fluctuation ratio differs depending on the control method as follows. - V/F control?????????2 to 5% (At the encode

Check the setting value of Pr.73. Or check Pr.C4 (Terminal 2 frequency setting gain) for the percentage of the voltage t

For tuning of a single motor with no load, set Pr.96 to "101". When a load is connected, set Pr.96 to "1" (without motor

The brake unit operates when the bus voltage exceeds the brake operation voltage.

Keep a clearance of "minimum 10cm each on top and bottom and minimum 5cm each on right and left".

It is compatible with the -R type FR-S500. (It is not compatible with the FR-S500 without -R because it does not have th

It controls the charging current immediately after the power is ON. (as a resistor for charging current limit circuit)

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1101-1110 of Total 1354

prev 111 / 136page next

Output specification between FM and SD

The output signal across FM and SD is pulse output. The output frequency and number of pulses of the output signal across FM and SD are proportional. However... More Details >>
- No：21384
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Comparison of the speed change rate

Speed fluctuation ratio differs depending on the control method as follows. - V/F control?????????2 to 5% (At the encoder feedback: 0.02%)- General-purpose m... More Details >>
- No：21377
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Analog voltage

Check the setting value of Pr.73. Or check Pr.C4 (Terminal 2 frequency setting gain) for the percentage of the voltage that is actually applied. For the FR-E... More Details >>
- No：21356
- Release Date：2018/08/22 16:27
- Category： FREQROL-E700
Real sensorless vector control

For tuning of a single motor with no load, set Pr.96 to "101". When a load is connected, set Pr.96 to "1" (without motor rotation). Since Real sensorless vec... More Details >>
- No：21325
- Release Date：2018/08/22 16:27
- Category： FREQROL-A700
Brake unit

The brake unit operates when the bus voltage exceeds the brake operation voltage. More Details >>
- No：21272
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
FR-CVL

Keep a clearance of "minimum 10cm each on top and bottom and minimum 5cm each on right and left". More Details >>
- No：21178
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-SW1-SETUP

It is compatible with the -R type FR-S500. (It is not compatible with the FR-S500 without -R because it does not have the PU connector and thus cannot be con... More Details >>
- No：21175
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Engineering Software
Using the inverter near a large power supply system

Use the AC reactor. More Details >>
- No：21171
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-HC2

It controls the charging current immediately after the power is ON. (as a resistor for charging current limit circuit) More Details >>
- No：21150
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
S-PM motor

It is not covered. More Details >>
- No：21132
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Others

1101-1110 of Total 1354

Inquiries

page top