Horizontal installation prevents heat release, resulting in a failure. Install the inverter vertically.

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor)

The reactor built in the FREQROL-A201 series is intended to stabilize operation of the converter circuit and differs fro

The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value d

Signals input from the terminal 4 are not enabled if the terminal AU is not ON. For an inverter without the terminal AU,

You can write frequency setting by setting Pr.339 (Communication speed command source) to "0".

This parameter cannot be changed in the external operation mode.Change Pr.77 (Parameter write selection) to "2" before c

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied af

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1111-1120 of Total 1353

prev 112 / 136page next

Installation direction

Horizontal installation prevents heat release, resulting in a failure. Install the inverter vertically. More Details >>
- No：21286
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Auto tuning

Normally, the auto tuning condition depends on the combination of the inverter and motor (including wiring to the motor), perform auto tuning each time. The ... More Details >>
- No：21293
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700PJ
Built-in reactor

The reactor built in the FREQROL-A201 series is intended to stabilize operation of the converter circuit and differs from the FR-BAL. Note that when performi... More Details >>
- No：21421
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options , Others
Speed setting

The high speed command (multi-speed command) is prioritized over the frequency setting potentiometer. It is OK if these are both input simultaneously. When t... More Details >>
- No：21424
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-U100
Countermeasure against error

The inverter alarm "OV3" occurs when the main circuit DC voltage inside the inverter goes higher than the preset value due to the regenerative power returned... More Details >>
- No：21438
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A024
Terminal

Signals input from the terminal 4 are not enabled if the terminal AU is not ON. For an inverter without the terminal AU, assign the AU function to an unused ... More Details >>
- No：21679
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Switching between external operation and NET operation

You can write frequency setting by setting Pr.339 (Communication speed command source) to "0". More Details >>
- No：21687
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

This parameter cannot be changed in the external operation mode.Change Pr.77 (Parameter write selection) to "2" before changing the setting of Pr.72. More Details >>
- No：21743
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

To set the frequency via CC-Link communication, the NET mode should be selected. The new parameter setting is applied after powering OFF and then ON the inve... More Details >>
- No：21763
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency setting

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is not shown as exactly 60 Hz.For V/F co... More Details >>
- No：21807
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700

1111-1120 of Total 1353

Inquiries

page top