You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch whil

It is not stored in a parameter but memorized as the frequency setting value after acceleration by the acceleration sign

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time.

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).

Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less.

Yes. Set the first monitor code in the lower 8 bits and the second monitor code in the upper 8 bits of RWwn.Set H6F to t

Using a reactor under a load lighter than the rated capacity slightly spoils its effect in improving the power factor.Th

Use Pr.17 (Input terminal assignment) to assign MRS to the terminals DI1, DI2, and DI3.

Set the parameters below. For other parameters, keep the initial settings.1. Set Pr.122 (Communication check time interv

When the inverter's forward and reverse terminals are switched instantaneously, the inverter decelerates and then switch

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1121-1130 of Total 1353

prev 113 / 136page next

Switching between external operation and NET operation

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch while Pr.79 (Operation mode) is set to "6... More Details >>
- No：21688
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

It is not stored in a parameter but memorized as the frequency setting value after acceleration by the acceleration signal.You can also choose whether or not... More Details >>
- No：21733
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Parameter

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time. More Details >>
- No：21769
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) instead of Pr.1 (Maximum frequency).　　 More Details >>
- No：21802
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency manual controller FR-AX

Considering voltage drop of the internal power supply and influence by noise, the wiring length should be 30 m or less. More Details >>
- No：21809
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

Yes. Set the first monitor code in the lower 8 bits and the second monitor code in the upper 8 bits of RWwn.Set H6F to the first monitor code, and H70 to the... More Details >>
- No：21824
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Using a higher grade power factor improving reactor

Using a reactor under a load lighter than the rated capacity slightly spoils its effect in improving the power factor.Therefore, you should use a reactor wit... More Details >>
- No：21935
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Coasting to stop method

Use Pr.17 (Input terminal assignment) to assign MRS to the terminals DI1, DI2, and DI3. More Details >>
- No：21937
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Inverter setup

Set the parameters below. For other parameters, keep the initial settings.1.　Set Pr.122 (Communication check time interval) to other than "0". ("9999" is OK.... More Details >>
- No：21986
- Release Date：2018/08/22 16:30
- Category： Engineering Software
Reversible operation of agitator

When the inverter's forward and reverse terminals are switched instantaneously, the inverter decelerates and then switches the rotation direction. It can swi... More Details >>
- No：21999
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL

1121-1130 of Total 1353

Inquiries

page top