Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresp

It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in op

It is not possible when the speed command is communication.

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked.

They are cleared by the RES signal from the external terminals or inverter reset from the communication.

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

"E.OSD" occurs when the rotation speed is not decreased for one second despite the start command (STF, STR) is turned OF

At power-ON, the signal turns ON for a moment to perform a converter initial reset.

It is 0.88 mm2 (AWG18), and 0.3 mm2 (AWG24) for the thermostat.

Yes, it can. When the FR-A7NF is installed, the CS terminal is disabled. Assign the CS terminal function to other input

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1121-1130 of Total 1353

prev 113 / 136page next

Replacement

Pr.38 of the E500 corresponds to Pr.125 (Terminal 2 frequency setting gain frequency) of D700. Pr.39 of the E500 corresponds to Pr.126 (Terminal 4 frequency ... More Details >>
- No：21254
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-D700
Dancer control during CC-Link communication

It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in operation. Example) When Pr.541 is set ... More Details >>
- No：21243
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Speed command by CC-Link communication

It is not possible when the speed command is communication. More Details >>
- No：21232
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Checking bit state by CC-Link communication

Because the H0F monitor only observes the ON/OFF of the hardware, it cannot be checked. More Details >>
- No：21230
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Communication EEPROM write selection (Pr.342)

They are cleared by the RES signal from the external terminals or inverter reset from the communication. More Details >>
- No：21221
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Vector control

"E.OSD" occurs when the rotation speed is not decreased for one second despite the start command (STF, STR) is turned OFF. More Details >>
- No：21159
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
FR-CV

At power-ON, the signal turns ON for a moment to perform a converter initial reset. More Details >>
- No：21156
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-HC2

It is 0.88 mm2 (AWG18), and 0.3 mm2 (AWG24) for the thermostat. More Details >>
- No：21147
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
FR-A7NF

Yes, it can. When the FR-A7NF is installed, the CS terminal is disabled. Assign the CS terminal function to other input terminals by setting the parameter. B... More Details >>
- No：21121
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Plug-in Options

1121-1130 of Total 1353

Inquiries

page top