The detection level of the output current value cannot be changed using a potentiometer or a similar device.

Slow blinking of the RUN LED indicates reverse operation.Fast blinking indicates that while the start command is input,

Set Pr.56 (Current monitor reference) to "10A".

It is OK if stations are set as reserved.

When the potentiometer is disconnected and frequency commands cease, the input potential becomes around 0 V.Therefore, t

Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary.

It is not recommended to start and stop the inverter with the electromagnetic contactor (MC). This will accelerate the d

As described in the instruction manual, use the shielded cable or twisted cable to avoid the influence of noises.

The output frequency is not changed by the maximum frequency setting. It can be changed by the following methods. - Set

You can change it by changing the setting of Pr.72 (PWM frequency selection). Setting range of Pr.72: 0, 1, 2, 3, 4, 5,

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1131-1140 of Total 1353

prev 114 / 136page next

Output current value

The detection level of the output current value cannot be changed using a potentiometer or a similar device.　　 More Details >>
- No：21779
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

Slow blinking of the RUN LED indicates reverse operation.Fast blinking indicates that while the start command is input, the running frequency command is not ... More Details >>
- No：21833
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Terminal FM

Set Pr.56 (Current monitor reference) to "10A". More Details >>
- No：21865
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

It is OK if stations are set as reserved. More Details >>
- No：21868
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency setting

When the potentiometer is disconnected and frequency commands cease, the input potential becomes around 0 V.Therefore, the frequency command becomes analog-c... More Details >>
- No：21794
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Rated frequency setting

Check that Pr.3 (Base frequency) is set to "200 Hz". Adjust Pr.0 (Torque boost) as necessary. More Details >>
- No：21280
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Electromagnetic contactor

It is not recommended to start and stop the inverter with the electromagnetic contactor (MC). This will accelerate the deterioration (due to the inrush curre... More Details >>
- No：21322
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Applied terminal

As described in the instruction manual, use the shielded cable or twisted cable to avoid the influence of noises. More Details >>
- No：21344
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

The output frequency is not changed by the maximum frequency setting. It can be changed by the following methods. - Set the frequency on the operation panel.... More Details >>
- No：21347
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Can I change the carrier frequency?

You can change it by changing the setting of Pr.72 (PWM frequency selection). Setting range of Pr.72: 0, 1, 2, 3, 4, 5, 6 (Initial setting is "6".) (The smal... More Details >>
- No：21640
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-V200

1131-1140 of Total 1353

Inquiries

page top