Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4".

Set Pr.125 (Terminal 2 frequency setting gain frequency) = "90 Hz".This changes the frequency with the potentiometer tur

You can do so by assigning the terminal AU.Assign the terminal AU to an unused terminal.(For example, when assigning AU

1. Stall prevention operation works when the inverter's output current exceeds the value set with Pr.22.In this case, it

The possible causes are as follows. While the inverter power supply is turned ON, inserting the modular jack to the conn

MR Configurator2 has been improved in the following. ・The servo assistant function introduces the related functions fo

If "HOLD" is displayed, the key lock mode enabled. Press the "MODE" key for two seconds. Then, change the setting of Pr.

Frequency meter: YM206NRI 1 mA Calibration resistor: RV24YN 10 k?.

1. Yes. 2. Set Pr.17 to "2". 3. If the start signal is ON, the operation continues even the emergency stop is OFF.

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1141-1150 of Total 1353

prev 115 / 136page next

CC-Link

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4". More Details >>
- No：21839
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) = "90 Hz".This changes the frequency with the potentiometer turned to the maximum position (at 5 V i... More Details >>
- No：21909
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

You can do so by assigning the terminal AU.Assign the terminal AU to an unused terminal.(For example, when assigning AU to the terminal RL, set Pr.180 = 4.)B... More Details >>
- No：21915
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Stall prevention

1. Stall prevention operation works when the inverter's output current exceeds the value set with Pr.22.In this case, it is considered that the current did n... More Details >>
- No：22067
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Communication fault occurs

The possible causes are as follows. While the inverter power supply is turned ON, inserting the modular jack to the connector with the operation panel remove... More Details >>
- No：22094
- Release Date：2018/08/22 16:30
- Category： Engineering Software
MR Configurator2

MR Configurator2 has been improved in the following. ・The servo assistant function introduces the related functions for each operation step to enable the f... More Details >>
- No：23658
- Release Date：2018/09/14 15:10
- Category： Servo Support Software
Easy setting mode

If "HOLD" is displayed, the key lock mode enabled. Press the "MODE" key for two seconds. Then, change the setting of Pr.79 to "1". More Details >>
- No：21350
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency meter and calibration resistor

Frequency meter: YM206NRI 1 mA Calibration resistor: RV24YN 10 k?. More Details >>
- No：21357
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
PU operation

1. Yes. 2. Set Pr.17 to "2". 　3. If the start signal is ON, the operation continues even the emergency stop is OFF. More Details >>
- No：21359
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-Configurator

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.　　 More Details >>
- No：21711
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

1141-1150 of Total 1353

Inquiries

page top