When the inverter's forward and reverse terminals are switched instantaneously, the inverter decelerates and then switch

The fan of the FR-A024 cannot be replaced by the customer. Mitsubishi Electric System & Service will replace it, so

When the command frequency is 0 Hz, the inverter does not generate output and the voltage is 0 V.

The AM-5 output is 0 to 10 VDC voltage output.Therefore, you need to install a voltmeter.Also, since the inverter output

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the fol

The specifications of the FR-V200E series do not allow for choosing from "Reset input always enabled" and "Reset input e

Since the inverter's fault contact is an NC contact, it does not open unless a fault occurs.Therefore, when the control

A motor overheats (the current increases) when the load is heavy.When the electronic thermal O/L relay works, you need t

You can install the operation panel FR-DU04 (or parameter unit FR-PU04) on the enclosure surface by connecting it with t

As an example, you can use an inverter to feed the cord at the constant speed under dancer control using a combination o

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1171-1180 of Total 1368

prev 118 / 137page next

Reversible operation of agitator

When the inverter's forward and reverse terminals are switched instantaneously, the inverter decelerates and then switches the rotation direction. It can swi... More Details >>
- No：21999
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Can I replace the cooling fan alone?

The fan of the FR-A024 cannot be replaced by the customer. Mitsubishi Electric System & Service will replace it, so contact us to order it. More Details >>
- No：22001
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A024
0 Hz output of inverter

When the command frequency is 0 Hz, the inverter does not generate output and the voltage is 0 V. More Details >>
- No：22011
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Installation method of AM-5 terminal ammeter

The AM-5 output is 0 to 10 VDC voltage output.Therefore, you need to install a voltmeter.Also, since the inverter output current is displayed, the scale of t... More Details >>
- No：22016
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-F500
Changing main speed at analog signal input

To change the running frequency while the frequency command is input to the terminal 2, adjust the parameters in the following steps:1. Change Pr.77 to "2".2... More Details >>
- No：22025
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Reset selection

The specifications of the FR-V200E series do not allow for choosing from "Reset input always enabled" and "Reset input enabled only when the protective funct... More Details >>
- No：22031
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Fault contact when connecting separate power supply for each control circuit

Since the inverter's fault contact is an NC contact, it does not open unless a fault occurs.Therefore, when the control power supply (and main circuit power ... More Details >>
- No：22035
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Consideration on thermal

A motor overheats (the current increases) when the load is heavy.When the electronic thermal O/L relay works, you need to mitigate the load.If the current is... More Details >>
- No：22042
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Installing parameter unit outside control panel

You can install the operation panel FR-DU04 (or parameter unit FR-PU04) on the enclosure surface by connecting it with the inverter via a cable.To do this, d... More Details >>
- No：22044
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Winding control

As an example, you can use an inverter to feed the cord at the constant speed under dancer control using a combination of the deviation detector and deviatio... More Details >>
- No：22047
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500

1171-1180 of Total 1368

Inquiries

page top