Only the unit type SC-A□□U has fault output signals. (Terminals Y1 and SD open collector output permissible load 24 VDC

To almost "1". (With load factor of 100%)

If the reactor 1, outside box, and reactor 2 are contained in the same case as the high power factor converter, the unit

When an instantaneous power failure of 100 msec or longer occurs, the inverter is reset* and it is not recognized as a f

If you connect two frequency setting potentiometers to the terminals 5 and 10, the permissible current of 10 mA is excee

1. Wiring length between the inverter and the motor should be 500 m or less. For 0.75 kW or lower motors, the followi

After inputting the start signal performing the tuning, output the output frequency. The tuning ends in approximately 5

The USB connection requires FR Configurator (FR-SW3-SETUP-WJ) prepared by Mitsubishi Electric Corporation.

The same test as CC-Link is performed, and we confirmed no problem.

The acceleration time is 60 Hz and 5 seconds, and deceleration time is 60 Hz and 60 seconds.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1181-1190 of Total 1353

prev 119 / 136page next

Fault output signal when inverter trips

Only the unit type SC-A□□U has fault output signals. (Terminals Y1 and SD open collector output permissible load 24 VDC 0.1 A)The box type SC-A□□B indicates ... More Details >>
- No：21580
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , SC-A
Input power factor

To almost "1". (With load factor of 100%) More Details >>
- No：21577
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Accessories and inverter with built-in high power factor converter

If the reactor 1, outside box, and reactor 2 are contained in the same case as the high power factor converter, the unit becomes larger and heavier while fre... More Details >>
- No：21573
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Faults history upon power failure

When an instantaneous power failure of 100 msec or longer occurs, the inverter is reset* and it is not recognized as a fault. Since it is not recognized as a... More Details >>
- No：21551
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Auxiliary input power supply

If you connect two frequency setting potentiometers to the terminals 5 and 10, the permissible current of 10 mA is exceeded, and you need to install 2 KΩ res... More Details >>
- No：21494
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Wire length between inverter and motor

1. Wiring length between the inverter and the motor should be 500 m or less. For 0.75 kW or lower motors, the following relationship is true: Capacity... More Details >>
- No：21392
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Magnetic flux and tuning

After inputting the start signal performing the tuning, output the output frequency. 　The tuning ends in approximately 500 ms in maximum after started. Durin... More Details >>
- No：21372
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
USB connector

The USB connection requires FR Configurator (FR-SW3-SETUP-WJ) prepared by Mitsubishi Electric Corporation. More Details >>
- No：21318
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Noise effect of CC-Link IE communication

The same test as CC-Link is performed, and we confirmed no problem. More Details >>
- No：21226
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-FS

The acceleration time is 60 Hz and 5 seconds, and deceleration time is 60 Hz and 60 seconds. More Details >>
- No：21166
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

1181-1190 of Total 1353

Inquiries

page top