You can change the full-scale value by changing Pr.55 (Frequency monitor reference). The initial setting is 60 Hz.

The FR-E500 manufactured before May 1998 behaved as you mentioned, and the potentiometer becomes unavailable once you se

1. How much is the sensitivity current? When the sum of the three-phase output current of the inverter reaches approxima

The parameter can be copied to only one inverter.

Air pressure falls by about 100 hPa for every 1,000 meters higher you go. This results in the air becomes thinner and a

Please refer to the section "Terminal box installation location and direction of lead wire outlet" of the general catalo

The detailed information of parameter, monitor, signal and alarm, etc. is available in Help of MR Configurator2. Select

1. By setting Pr.158 (Terminal AM function selection) to "21" (Reference voltage output), 10 V is output from the termin

Set Pr.3 (Base frequency) and Pr.18 (High speed maximum frequency) to "340 Hz", Pr.19 (Base frequency voltage) to "200 V

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz".

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

111-120 of Total 1368

prev 12 / 137page next

Full scale frequency

You can change the full-scale value by changing Pr.55 (Frequency monitor reference). The initial setting is 60 Hz. More Details >>
- No：21672
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-E520 operation mode (Pr.79) selection

The FR-E500 manufactured before May 1998 behaved as you mentioned, and the potentiometer becomes unavailable once you set the frequency on the operation pane... More Details >>
- No：21525
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E500
Output side earth (ground) fault overcurrent protection

1. How much is the sensitivity current? When the sum of the three-phase output current of the inverter reaches approximately 70% of the inverter rated curren... More Details >>
- No：21394
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-A024 , FREQROL-E500
Parameter copy of FR-Configurator

The parameter can be copied to only one inverter. More Details >>
- No：21306
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Regarding altitude restrictions

Air pressure falls by about 100 hPa for every 1,000 meters higher you go. This results in the air becomes thinner and a drop in cooling capacity. This can re... More Details >>
- No：20781
- Release Date：2018/08/21 16:10
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type , S-PM Geared Motors Parallel shaft type , S-PM Geared Motors Right angle shaft type
About changing the direction of the cable entrance for the terminal box

Please refer to the section "Terminal box installation location and direction of lead wire outlet" of the general catalogue. However, GM-J2 series is not su... More Details >>
- No：20763
- Release Date：2018/08/21 16:10
- Update：2018/09/04 15:06
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type , S-PM Geared Motors Parallel shaft type , S-PM Geared Motors Right angle shaft type
Details of monitor list

The detailed information of parameter, monitor, signal and alarm, etc. is available in Help of MR Configurator2. Select the servo amplifier being used to che... More Details >>
- No：23634
- Release Date：2018/09/14 15:10
- Category： Servo Support Software
Terminal AM calibration

1. By setting Pr.158 (Terminal AM function selection) to "21" (Reference voltage output), 10 V is output from the terminal AM.2. Read Pr.901 in the PU operat... More Details >>
- No：21936
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-F500 , FREQROL-A200 , FREQROL-A100
Frequency setting

Set Pr.3 (Base frequency) and Pr.18 (High speed maximum frequency) to "340 Hz", Pr.19 (Base frequency voltage) to "200 V", Pr.125 (Terminal 2 frequency setti... More Details >>
- No：21789
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Parameter setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz". More Details >>
- No：21720
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

111-120 of Total 1368

Inquiries

page top