Horizontal installation prevents heat release, resulting in a failure. Install the inverter vertically.

Since the multi-speed is given a higher priority, the setting by the setting dial is not enabled unless all of the multi

For an inverter with the terminal AU, use the terminal AU. For other inverters, assign the AU function to an unused term

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz".

It cannot be avoided by using parameters.

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time.

EN standard is a unified standard concerning safety in Europe, takes precedence over the regulations and standards of ea

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (again

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1201-1210 of Total 1368

prev 121 / 137page next

Installation direction

Horizontal installation prevents heat release, resulting in a failure. Install the inverter vertically. More Details >>
- No：21286
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-PA07

Since the multi-speed is given a higher priority, the setting by the setting dial is not enabled unless all of the multi-speed signals are OFF. More Details >>
- No：21302
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Terminal

For an inverter with the terminal AU, use the terminal AU. For other inverters, assign the AU function to an unused terminal. And, short-circuit (turn ON) th... More Details >>
- No：21678
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
FR-Configurator

Yes, you can use the setup software (FR-SW3-SETUP-WJ) to set it.　　 More Details >>
- No：21711
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Parameter setting

Set Pr.125 (Terminal 2 frequency setting gain frequency) to "50 Hz".Set Pr.1 (Maximum frequency) to "50 Hz". More Details >>
- No：21720
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Electromagnetic contactor

It cannot be avoided by using parameters.　　 More Details >>
- No：21724
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
NET mode

After setting Pr.340 to "10", you need to power OFF then ON the inverter to make the new setting enabled because you are setting the operation upon power-on.... More Details >>
- No：21759
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Parameter

No parameter can be used to directly set this time.Changing Pr.9 (Electronic thermal O/L relay) changes the time. More Details >>
- No：21769
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
About complying with EN standard

EN standard is a unified standard concerning safety in Europe, takes precedence over the regulations and standards of each European countries. The manufactur... More Details >>
- No：20769
- Release Date：2018/08/21 16:10
- Update：2018/09/04 14:16
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type , S-PM Geared Motors Parallel shaft type , S-PM Geared Motors Right angle shaft type
Electromagnetic contactor

Turning ON/OFF the output side during operation causes open/close surges that may trigger the protective function (against overcurrent or overvoltage) of the... More Details >>
- No：21725
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

1201-1210 of Total 1368

Inquiries

page top