If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with

The inverter has the calibration function.Use Pr.125 (Terminal 2 frequency setting gain frequency) and Pr.C4 (Terminal 2

Change Pr.79 (Operation mode) to "3" (Combined operation mode) and short-circuit the external terminals STF and SD (or S

Set Pr.56 (Current monitor reference) to "10A".

1. Yes. The inverter cannot restart if STF and STR are turned OFF.However, on the next startup, the inverter detects coa

The “current command” is the command value for the current control (torque control) and the “torque” is the feedback val

Using MR Configurator2, you can perform the positioning operation when there is no command from the controller. You can

Yes. Parameters can be read except during an inverter reset or when the password function is set.

No. (Using the copy function causes an error.) Use the FR-DU08 when performing the copy function of the operation panel.

The total wiring length is as follows: 100 m + (20 m × 5) = 200m.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1211-1220 of Total 1368

prev 122 / 137page next

Minimum frequency

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with Pr.13 (Starting frequency) up to 3 H... More Details >>
- No：21777
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
External operation

The inverter has the calibration function.Use Pr.125 (Terminal 2 frequency setting gain frequency) and Pr.C4 (Terminal 2 frequency setting gain) for calibrat... More Details >>
- No：21849
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Parameter setting

Change Pr.79 (Operation mode) to "3" (Combined operation mode) and short-circuit the external terminals STF and SD (or STR and SD for reverse rotation). More Details >>
- No：21859
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Terminal FM

Set Pr.56 (Current monitor reference) to "10A". More Details >>
- No：21865
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Automatic restart after instantaneous power failure

1. Yes. The inverter cannot restart if STF and STR are turned OFF.However, on the next startup, the inverter detects coasting and restarts.2. When automatic ... More Details >>
- No：21942
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-V200
Difference between the current command and torque

The “current command” is the command value for the current control (torque control) and the “torque” is the feedback value controlled by the current control ... More Details >>
- No：23624
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE , MELSERVO-JN , MELSERVO-J3 , MELSERVO Others
Positioning operation

Using MR Configurator2, you can perform the positioning operation when there is no command from the controller. You can perform the operation specifying the ... More Details >>
- No：23640
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4 , MELSERVO-JE , MELSERVO-JN , MELSERVO-J3
Parameter copy to the USB memory

Yes. Parameters can be read except during an inverter reset or when the password function is set. More Details >>
- No：20961
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800
Copy function

No. (Using the copy function causes an error.) Use the FR-DU08 when performing the copy function of the operation panel. More Details >>
- No：21118
- Release Date：2018/08/22 16:26
- Category： FREQROL-A800 , Options , FREQROL-F800
Wiring length

The total wiring length is as follows: 100 m + (20 m × 5) = 200m. More Details >>
- No：21144
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

1211-1220 of Total 1368

Inquiries

page top