Z phase is not required for the thickness method.

It is the same as the one by the inverter whose capacity is one-rank higher than the FR-A500L series.

If the current increases when the motor stops under V/F control (at low speed under a light load), the motor is consider

This error depends on the application and the cause is unknown. (The runtime error '31037' is not returned from this app

Grounding can often get dirty due to influence from the inverter main circuit switching. Therefore, when the potentiomet

After inputting the start signal performing the tuning, output the output frequency. The tuning ends in approximately 5

Because the multi-speed terminal is disabled, it does not operate in multi-speed.

The function block and ladder language are available. The ST language is not available.

Using a motor dedicated to the direct connection (with a creep-free bearing) may result in a bearing noise.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1261-1270 of Total 1353

prev 127 / 136page next

Winding diameter calculation of the FR-A800-R2R

Z phase is not required for the thickness method. More Details >>
- No：20855
- Release Date：2018/08/22 16:24
- Category： FREQROL-A800
Amount of heat generated by the FR-V500L

It is the same as the one by the inverter whose capacity is one-rank higher than the FR-A500L series. More Details >>
- No：20854
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
Current increase at motor stop

If the current increases when the motor stops under V/F control (at low speed under a light load), the motor is considered to be in the overexcitation state.... More Details >>
- No：21997
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Not operating on Windows95

This error depends on the application and the cause is unknown. (The runtime error '31037' is not returned from this application but from the OS (Windows).) ... More Details >>
- No：21495
- Release Date：2018/08/22 16:27
- Category： Engineering Software
Shielded wiring of external speed setting potentiometer

Grounding can often get dirty due to influence from the inverter main circuit switching. Therefore, when the potentiometer shielded wire is connected to the ... More Details >>
- No：21455
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Magnetic flux and tuning

After inputting the start signal performing the tuning, output the output frequency. 　The tuning ends in approximately 500 ms in maximum after started. Durin... More Details >>
- No：21372
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Remote setting function

Because the multi-speed terminal is disabled, it does not operate in multi-speed. More Details >>
- No：21205
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
PLC function

The function block and ladder language are available. The ST language is not available. More Details >>
- No：21043
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
MM-EF/EFS

Using a motor dedicated to the direct connection (with a creep-free bearing) may result in a bearing noise. More Details >>
- No：20963
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Others
Safety stop function of the FR-E700/FR-D700

Up to two. More Details >>
- No：20827
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL

1261-1270 of Total 1353

Inquiries

page top