MR Configurator2 has been improved in the following. ・The servo assistant function introduces the related functions fo

1. For MRS, coasting starts when the MRS contact turns ON. For Pr.250 = "0",IM is coasting immediately when the start si

The inverter uses PWM control to change the output voltage and frequency to vary the motor speed. PWM stands for Pulse W

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you

From Start menu of Windows >, click [All Programs] > - [MELSOFT Application] > - [MR Configurator2] > and y

Normally, Pr.80 and Pr.81 are the parameters that can be changed when the operation is stopped in the PU operation mode.

An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the ma

1. No operation log is recorded.2. No. However, you can create a state indicating that automatic restart after instantan

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are

Set Pr.146 (Built-in potentiometer switching) to "0".This allows for using the potentiometer built in the FR-PA02 to set

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1291-1300 of Total 1354

prev 130 / 136page next

MR Configurator2

MR Configurator2 has been improved in the following. ・The servo assistant function introduces the related functions for each operation step to enable the f... More Details >>
- No：23658
- Release Date：2018/09/14 15:10
- Category： Servo Support Software
MRS setting

1. For MRS, coasting starts when the MRS contact turns ON. For Pr.250 = "0",IM is coasting immediately when the start signal is turned OFF. 　2. No. Set eithe... More Details >>
- No：21360
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Soft-PWM

The inverter uses PWM control to change the output voltage and frequency to vary the motor speed. PWM stands for Pulse Width Modulation. Voltage is chopped i... More Details >>
- No：21549
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Calculation of acceleration/deceleration time

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you should consider a factor of 120% for ... More Details >>
- No：21965
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
MR-J4(W)-B mode selection application

From Start menu of Windows >, click [All Programs] > - [MELSOFT Application] > - [MR Configurator2] > and you can find “MR-J4(W)-B mode selectio... More Details >>
- No：23637
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4
Parameter display setting

Normally, Pr.80 and Pr.81 are the parameters that can be changed when the operation is stopped in the PU operation mode. The "Er4" is a mode designation erro... More Details >>
- No：21335
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Detection of the motor load

An inverter is used to rotate a motor but it cannot be used to detect whether the belt is broken or not. However, the magnitude of the load will change when ... More Details >>
- No：21387
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Operation of automatic restart after instantaneous power failure

1. No operation log is recorded.2. No. However, you can create a state indicating that automatic restart after instantaneous power failure is in progress by ... More Details >>
- No：21948
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
FR-A5CN

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of water. More Details >>
- No：21435
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Operation panel (FR-PA02)

Set Pr.146 (Built-in potentiometer switching) to "0".This allows for using the potentiometer built in the FR-PA02 to set the frequency.(Set this parameter to... More Details >>
- No：21729
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ

1291-1300 of Total 1354

Inquiries

page top