When the DIP switch is changed to I, it does not operate normally because the internal resistance changes.

Square wave input is not recommended since it can cause failures (for example, damage the diode bridge).

As you mention, when the inverter is operated only with STF without inputting the speed command signal, the minimum freq

By attaching the optional card and dedicated cover, the depth increases by approximately 15 mm for the FR-E700, and appr

A reference sine wave signal is generated inside the high power factor converter, and transistors are configured and PWM

Since the converter in the high power factor converter section performs PWM switching, the leakage current increases to

An inverter with one-rank higher capacity is often used when a high torque is required for a short period of time. (Exam

No. During JOG operation, deceleration stop is performed even though Pr.250 is set.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1291-1300 of Total 1353

prev 130 / 136page next

FR-A800-CRN

Yes, it is included. More Details >>
- No：20933
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Terminal 2 input selector switch when the PTC thermistor is connected

When the DIP switch is changed to I, it does not operate normally because the internal resistance changes. More Details >>
- No：20901
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
Safety stop function of the FR-E700/FR-D700

Up to two. More Details >>
- No：20827
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
Inverter input power supply

Square wave input is not recommended since it can cause failures (for example, damage the diode bridge). More Details >>
- No：22106
- Release Date：2018/08/22 16:31
- Category： Inverters-FREQROL , FREQROL-E500
Switching between high speed and low speed

As you mention, when the inverter is operated only with STF without inputting the speed command signal, the minimum frequency must be set to 10 Hz.However, a... More Details >>
- No：22078
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
CC-Link

By attaching the optional card and dedicated cover, the depth increases by approximately 15 mm for the FR-E700, and approximately 22 mm for the FR-E700-SC.Si... More Details >>
- No：21835
- Release Date：2018/08/22 16:29
- Category： FREQROL-E700
Waveform improvement

A reference sine wave signal is generated inside the high power factor converter, and transistors are configured and PWM switching is performed in the conver... More Details >>
- No：21574
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Influence on leakage current

Since the converter in the high power factor converter section performs PWM switching, the leakage current increases to the same level as the general-purpose... More Details >>
- No：21558
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Inverter with one-rank higher capacity

An inverter with one-rank higher capacity is often used when a high torque is required for a short period of time. (Examples)- When rapid acceleration/decele... More Details >>
- No：21456
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Stop selection

No. During JOG operation, deceleration stop is performed even though Pr.250 is set. More Details >>
- No：21199
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

1291-1300 of Total 1353

Inquiries

page top