Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the commun

The monitor with the code H01 switches by changing Pr.37 and Pr.144.

When performing the PID control by CC-Link communication, the X14 signal is disabled.

Only one instruction is executed. The instruction to be executed is not fixed.

No error will occur because up to 400 Hz that is the upper limit of the setting range can be written.

Other than "0" can be input. The inverter is reset by writing any numerical value.

Refer to the inverter capacity.

No. During JOG operation, deceleration stop is performed even though Pr.250 is set.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

1301-1310 of Total 1353

prev 131 / 136page next

Frequency setting

Ensure that the inverter is in the PU operation mode and stopped, change the following parameters: 1. Read Pr.923 (Built-in frequency setting potentiometer g... More Details >>
- No：21416
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Remote input signal of CC-Link communication

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the communication establishes again, the bit tu... More Details >>
- No：21237
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Monitor code of CC-Link communication

The monitor with the code H01 switches by changing Pr.37 and Pr.144. More Details >>
- No：21236
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
PID control of CC-Link communication

When performing the PID control by CC-Link communication, the X14 signal is disabled. More Details >>
- No：21233
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Instruction code execution request of CC-Link communication

Only one instruction is executed. The instruction to be executed is not fixed. More Details >>
- No：21231
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Writing set frequency by CC-Link communication

No error will occur because up to 400 Hz that is the upper limit of the setting range can be written. More Details >>
- No：21229
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

Other than "0" can be input. The inverter is reset by writing any numerical value. More Details >>
- No：21224
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Wiring length

Refer to the inverter capacity. More Details >>
- No：21200
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Stop selection

No. During JOG operation, deceleration stop is performed even though Pr.250 is set. More Details >>
- No：21199
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
CAD data

They are not available. More Details >>
- No：21138
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Others

1301-1310 of Total 1353

Inquiries

page top