It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-t

For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is

You can use an inverter for fan and pump with the compressor, but it is not recommended for an application that the moto

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% to

The harmonics generation device manufacturer application form must be created by the manufacturer and submitted by the c

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you c

The tension controller is suitable for the equipment with low speed and small capacity. The tension controller is suitab

For the inverter with capacity of 160K or higher, the fuse is built in its DC part.

Because RSO (converter reset) of the HC2 is connected to RES of the inverter, the inverter is reset along with the HC2 r

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

151-160 of Total 1353

prev 16 / 136page next

Specifications

It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-third or less of the inverter rated cu... More Details >>
- No：21282
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
Priority of multi-speed setting and frequency setting signals

For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is input, the inverter switch to multi-s... More Details >>
- No：21400
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Compressor

You can use an inverter for fan and pump with the compressor, but it is not recommended for an application that the motor load rapidly increases. More Details >>
- No：21443
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A100
Motor heat generation at low-speed operation

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% torque at up to 3 Hz does not cause a h... More Details >>
- No：21496
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Harmonic Suppression Guidelines

The harmonics generation device manufacturer application form must be created by the manufacturer and submitted by the consumer when a device that contains a... More Details >>
- No：21507
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Separation of operation panel

The operation panel of the FR-S500 is not detachable.For the FR-S500-○○K-R (compatible with RS-485 communication), you can install the FR-PU04 on the enclosu... More Details >>
- No：22058
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
FR-B/B3 (A800)

Yes, they are. More Details >>
- No：20877
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR-A800-R2R

The tension controller is suitable for the equipment with low speed and small capacity. The tension controller is suitable for the equipment with low speed a... More Details >>
- No：20929
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Inverter built-in fuse

For the inverter with capacity of 160K or higher, the fuse is built in its DC part. More Details >>
- No：20940
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options
FR-HC2

Because RSO (converter reset) of the HC2 is connected to RES of the inverter, the inverter is reset along with the HC2 reset. (Refer to the wiring diagram in... More Details >>
- No：20948
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options

151-160 of Total 1353

Inquiries

page top