The terminal MRS assignment parameter is Pr.183. Set Pr.183 to "4" (AU). (This setting is for the E700.)

The power supply voltage may have dropped.Read the converter output voltage monitor (Pr.55 = 8) and check if Converter o

During non-low-noise operation (initial setting) with the carrier frequency of 1 kHz, both noise and leakage current lev

Setting of Pr.408 (Thermistor selection) is required. Set as follows. For the model of SF-V5RU ending with "T" (SF-V5RU○

Yes, the English version of SW3 is included.

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are

The number of terminals: There are the same input terminals as F700P and the following terminals (4 points) are added. S

UVT will occur when reactor is not connected. Always connect a reactor that matches the motor capacity.

The phase detection terminal has been provided with units produced since December 1999. You can identify these units wit

Increasing the value of Pr.0 (Torque boost) increases the output voltage, and the output current also increases.Note tha

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

171-180 of Total 1353

prev 18 / 136page next

Terminal assignment

The terminal MRS assignment parameter is Pr.183. Set Pr.183 to "4" (AU). (This setting is for the E700.) More Details >>
- No：21850
- Release Date：2018/08/22 16:29
- Category： FREQROL-E700
Running frequency

The power supply voltage may have dropped.Read the converter output voltage monitor (Pr.55 = 8) and check if Converter output voltage monitor/√2 is within th... More Details >>
- No：21820
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Do noise and leakage current increase?

During non-low-noise operation (initial setting) with the carrier frequency of 1 kHz, both noise and leakage current levels are almost same as the Z024 serie... More Details >>
- No：21606
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Setting when using the FR-A7AZ and SF-V5RU

Setting of Pr.408 (Thermistor selection) is required. Set as follows. For the model of SF-V5RU ending with "T" (SF-V5RU○○T): Pr.408 = 0 For the model of SF-V... More Details >>
- No：21169
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR Configurator2

Yes, the English version of SW3 is included. More Details >>
- No：20912
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Engineering Software
FR-A5CN

When the heat sink is outside, since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of water. More Details >>
- No：21435
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
The number of input terminals

The number of terminals: There are the same input terminals as F700P and the following terminals (4 points) are added. Safety: SI1, SI2, SIC 24 V power suppl... More Details >>
- No：21070
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-F800
FR-A800

UVT will occur when reactor is not connected. Always connect a reactor that matches the motor capacity. More Details >>
- No：20978
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
Phase detection terminal

The phase detection terminal has been provided with units produced since December 1999. You can identify these units with the serial number "N9Z○○○○○○" or la... More Details >>
- No：22090
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Output current

Increasing the value of Pr.0 (Torque boost) increases the output voltage, and the output current also increases.Note that increasing this value too high puts... More Details >>
- No：21732
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

171-180 of Total 1353

Inquiries

page top