Yes, it is. However, it is not suitable for the low speed regenerative side. It is also recommended to use a dedicated c

The tension controller is suitable for the equipment with low speed and small capacity. The tension controller is suitab

Since the lower limit has been internally set, the setting value of 3 % or less is recognized as 3%.

The FR-A800 has metal installation holes regardless of the capacity.

It is a gap intentionally set in the movement direction between the machine elements that mesh with each other such as a

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is rever

Other than "0" can be input. The inverter is reset by writing any numerical value.

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the commun

The communication is established if DA, DB, and DG are connected each other.

It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in op

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

181-190 of Total 1353

prev 19 / 136page next

FR-A800-R2R

Yes, it is. However, it is not suitable for the low speed regenerative side. It is also recommended to use a dedicated control for winding/unwinding applicat... More Details >>
- No：20928
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-A800-R2R

The tension controller is suitable for the equipment with low speed and small capacity. The tension controller is suitable for the equipment with low speed a... More Details >>
- No：20929
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
FR-A800

Since the lower limit has been internally set, the setting value of 3 % or less is recognized as 3%. More Details >>
- No：20976
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
FR-A800

The FR-A800 has metal installation holes regardless of the capacity. More Details >>
- No：20980
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
Backlash

It is a gap intentionally set in the movement direction between the machine elements that mesh with each other such as a cogwheel used for the reduction gear. More Details >>
- No：21065
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Others
LED blinking under encoder feedback control

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is reversed. - The signal from the encoder is... More Details >>
- No：21219
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
System environment variable of the Modbus-RTU communication

Other than "0" can be input. The inverter is reset by writing any numerical value. More Details >>
- No：21224
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote input signal of CC-Link communication

When the communication error occurs, the input signal status is not retained, and all the bits turn OFF. When the communication establishes again, the bit tu... More Details >>
- No：21237
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Wiring of CC-Link communication cable

The communication is established if DA, DB, and DG are connected each other. More Details >>
- No：21239
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Dancer control during CC-Link communication

It is not possible under the dancer control. When the negative data is written, it is handled as the positive data in operation. Example) When Pr.541 is set ... More Details >>
- No：21243
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

181-190 of Total 1353

Inquiries

page top