Set Pr.338 (Operation command source) to "1" (external terminal).Set Pr.339 (Speed command source) to "0" (communication

Set Pr.56 (Current monitor reference) to "10A".

No. This is because the current cannot flow if the total internal impedance of the meter connected to the terminal FM is

The operation panel FR-PA02 for the FR-E500 can be used for these models.You need the FR-E5P (back cover adapter set) an

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is

The calibration parameter C6 (Terminal 4 frequency setting bias) is initially set to "20%". Therefore, voltage input to

Press the "SET" key once while the output frequency is monitored.The unit indicator LED changes from "Hz" to "A" and the

Under a 50% torque limit, if the commanded speed (50 Hz in your example) cannot be achieved without torque exceeding 50%

The following causes are probable for persistent Err. display: 1. The terminals RES and SD are always short-circuited. 2

1. For MRS, coasting starts when the MRS contact turns ON. For Pr.250 = "0",IM is coasting immediately when the start si

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

181-190 of Total 1353

prev 19 / 136page next

Frequency setting

Set Pr.338 (Operation command source) to "1" (external terminal).Set Pr.339 (Speed command source) to "0" (communication).Check the setting of Pr.79 for oper... More Details >>
- No：21869
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Terminal FM

Set Pr.56 (Current monitor reference) to "10A". More Details >>
- No：21865
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Terminal FM

No. This is because the current cannot flow if the total internal impedance of the meter connected to the terminal FM is 300 Ω or higher.You can connect mult... More Details >>
- No：21864
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Operation panel for FR-E500

The operation panel FR-PA02 for the FR-E500 can be used for these models.You need the FR-E5P (back cover adapter set) and FR-C20□ (connection cable) for the ... More Details >>
- No：21860
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ
Frequency setting

Since the Advanced magnetic flux vector control method uses slip compensation to compensate the frequency, the value is not shown as exactly 60 Hz.For V/F co... More Details >>
- No：21807
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Frequency setting

The calibration parameter C6 (Terminal 4 frequency setting bias) is initially set to "20%". Therefore, voltage input to the terminal 4 does not become effect... More Details >>
- No：21806
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Monitor indicator

Press the "SET" key once while the output frequency is monitored.The unit indicator LED changes from "Hz" to "A" and the monitor display changes to the current. More Details >>
- No：21764
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Operation under torque limit in the speed control mode

Under a 50% torque limit, if the commanded speed (50 Hz in your example) cannot be achieved without torque exceeding 50%, since the torque does not exceed th... More Details >>
- No：21483
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Dealing with Err.

The following causes are probable for persistent Err. display: 1. The terminals RES and SD are always short-circuited. 2. Operation panel contact or operatio... More Details >>
- No：21412
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
MRS setting

1. For MRS, coasting starts when the MRS contact turns ON. For Pr.250 = "0",IM is coasting immediately when the start signal is turned OFF. 　2. No. Set eithe... More Details >>
- No：21360
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

181-190 of Total 1353

Inquiries

page top