Under 100% load, the power factors of the AC and DC reactors are 90% and 95%, respectively. For a line with no inverter

Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during

If Pr.79 = 3, PU and EXT turn ON. Switching between PU and EXT is not available. Turn the setting dial to set the freque

From Start menu of Windows >, click [All Programs] > - [MELSOFT Application] > - [MR Configurator2] > and y

You can drive multiple motors with a single inverter.However, since the inverter cannot determine the current of each mo

Change Pr.340 (Communication startup mode selection) from "1" to "0".Power OFF and then ON the inverter.Operate the inve

Even after setting Pr.340 to "10", the change is reflected after resetting the power supply.Perform the power reset.Sinc

The following causes are probable for this Err display:- Operation error (for example, you tried to input a value other

1. Stall prevention operation works when the inverter's output current exceeds the value set with Pr.22.In this case, it

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

11-20 of Total 1368

prev 2 / 137page next

Power factor of inverter drive

Under 100% load, the power factors of the AC and DC reactors are 90% and 95%, respectively. For a line with no inverter control, use a power factor correctio... More Details >>
- No：21934
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Switching External operation, PU operation

Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during External operation switches the mode ... More Details >>
- No：21289
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
PU operation

If Pr.79 = 3, PU and EXT turn ON. Switching between PU and EXT is not available. Turn the setting dial to set the frequency and press the SET key to accept it. More Details >>
- No：21695
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
MR-J4(W)-B mode selection application

From Start menu of Windows >, click [All Programs] > - [MELSOFT Application] > - [MR Configurator2] > and you can find “MR-J4(W)-B mode selectio... More Details >>
- No：23637
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4
Can I drive multiple motors with a single inverter?

You can drive multiple motors with a single inverter.However, since the inverter cannot determine the current of each motor, the electronic thermal O/L relay... More Details >>
- No：22084
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Operation mode, PU operation mode switching

Change Pr.340 (Communication startup mode selection) from "1" to "0".Power OFF and then ON the inverter.Operate the inverter according to the value of Pr.79 ... More Details >>
- No：21870
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Switching between PU and NET operations

Even after setting Pr.340 to "10", the change is reflected after resetting the power supply.Perform the power reset.Since changes to the communication parame... More Details >>
- No：21696
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Err display on operation panel

The following causes are probable for this Err display:- Operation error (for example, you tried to input a value other than the available range of parameter... More Details >>
- No：22063
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Stall prevention

1. Stall prevention operation works when the inverter's output current exceeds the value set with Pr.22.In this case, it is considered that the current did n... More Details >>
- No：22067
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Calculation of acceleration/deceleration time

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you should consider a factor of 120% for ... More Details >>
- No：21965
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive

11-20 of Total 1368

Inquiries

page top