Drive Products

Start main contents

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

191-200 of Total 1368

prev 20 / 137page next

Applied motor selection

As the motor operates with the electronic thermal O/L relay characteristics for the standard motor, the thermal error occurs if the motor continuously operat... More Details >>
- No：21943
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Intercompatibility attachment

Use the FR-AAT04 (FR-Z series intercompatibility attachment). More Details >>
- No：21928
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-Z300
FR-Configurator

The FR Configurator FR-SW3-SETUP-WJ can only allow for test operation.Since this is a tool to support the system launch and maintenance, it is not designed f... More Details >>
- No：21914
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
NET mode, external operation switching

You can switch between the NET mode and external operation.Assign the X66 signal (Operation switching) to an unused terminal for switching.Also, set Pr.79 (O... More Details >>
- No：21906
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Auto tuning

Check if any device is connected to the inverter's external terminal.In particular, check if MRS and SD are short-circuited.If they are short-circuited, open... More Details >>
- No：21753
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Switching between external operation ...

You can write frequency setting by setting Pr.339 (Communication speed command source) to "0". More Details >>
- No：21687
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

Yes, you can set Pr.20 to 20 Hz. More Details >>
- No：21683
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
General-purpose magnetic flux control

Almost same control method. This control also performs vector calculation and divides the inverter's output current into an excitation current and into a tor... More Details >>
- No：21620
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A024
Sensitivity current of earth leakage ...

The rated sensitivity current of the earth leakage circuit breaker can be calculated using the following equation. If the result is 30 mA or less, the NV-FA ... More Details >>
- No：21547
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Peripheral devices
Overcurrent at low speed

"8" display in offline auto tuning means forced stop by the operator. This means that you stopped operation before tuning completes. 　With this forced stop, ... More Details >>
- No：21527
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500

191-200 of Total 1368

page top

PRAZNA logo