It is fundamentally the same as the conventional model. Considering the recent safety awareness growth, we decided to st

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is rever

Only one instruction is executed. The instruction to be executed is not fixed.

When performing the PID control by CC-Link communication, the X14 signal is disabled.

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises

No, it is not changed. Pr.268 is the parameter for the operation panel.

The ferrule terminal or single wire can be used for the control circuit wiring.

It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-t

The following USB connectors are available.For FR-A700: USB B connector (B receptacle)For FR-E700: USB Mini-B connector

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

231-240 of Total 1368

prev 24 / 137page next

Carrier frequency

It is fixed to 5 kHz. More Details >>
- No：21211
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-HC2

It is fundamentally the same as the conventional model. Considering the recent safety awareness growth, we decided to start supporting it from the FR-HC2. Be... More Details >>
- No：21212
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is reversed. - The signal from the encoder is... More Details >>
- No：21219
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Instruction code execution request of CC-Link communication

Only one instruction is executed. The instruction to be executed is not fixed. More Details >>
- No：21231
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
PID control of CC-Link communication

When performing the PID control by CC-Link communication, the X14 signal is disabled. More Details >>
- No：21233
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Earthing (grounding) of FR-A7NC (E kit)

There is no problem, however, earthing (grounding) from each FG terminal is recommended to avoid the influence of noises. More Details >>
- No：21240
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Pr.268 (Monitor decimal digits selection) during CC-Link communication

No, it is not changed. Pr.268 is the parameter for the operation panel. More Details >>
- No：21241
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Wiring and terminal

The ferrule terminal or single wire can be used for the control circuit wiring. More Details >>
- No：21275
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
Specifications

It can be driven by connecting single-phase 200 V to the terminals R and S. In this case, the load current must be one-third or less of the inverter rated cu... More Details >>
- No：21282
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700
Connection cable of FR-Configurator

The following USB connectors are available.For FR-A700: USB B connector (B receptacle)For FR-E700: USB Mini-B connector (Mini-B receptacle) Use the USB cable... More Details >>
- No：21317
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700

231-240 of Total 1368

Inquiries

page top