The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is rever

It is necessary to select the size of the reduction gear section that has mechanical strength equivalent to the output c

You can use general-purpose three-phase induction motors.You can also use geared motors if the motor itself is an induct

The one-touch tuning does not require the response level setting also. Outlines of one-touch tuning and auto tuning are

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the ou

The low-voltage manual contactor is intended to prevent electric shock during inspection and maintenance of the drive un

Since the FR-A540-0.75K has a brake transistor for resistor regenerative driving inside the inverter, you do not need to

The major changes from FR-AU01 to FR-AU01A include 1. Case material and 2. Lead wire terminal process method. The FR-AU0

When the inverter output shutoff signal MRS is turned on, the output is shut off immediately without regard to setting o

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

231-240 of Total 1353

prev 24 / 136page next

LED blinking under encoder feedback control

The following may be the cause. - No encoder power supply. - The setting of Pr.359 (Encoder rotation direction) is reversed. - The signal from the encoder is... More Details >>
- No：21219
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Insulation level of the MM-EFS

F class (155 deg C) More Details >>
- No：20809
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Others
Regarding service factors

It is necessary to select the size of the reduction gear section that has mechanical strength equivalent to the output converted to steady load condition tak... More Details >>
- No：20779
- Release Date：2018/08/21 16:10
- Category： Geared Motors Parallel shaft type , Geared Motors Right angle shaft type , S-PM Geared Motors Parallel shaft type , S-PM Geared Motors Right angle shaft type
Which motors can I use with the inverter?

You can use general-purpose three-phase induction motors.You can also use geared motors if the motor itself is an induction motor.Synchronous motors are not ... More Details >>
- No：22081
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
One-touch tuning

The one-touch tuning does not require the response level setting also. Outlines of one-touch tuning and auto tuning are as follows: One-touch tuning: You can... More Details >>
- No：23629
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE
Pulse train output of terminal FM

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the output frequency monitor value to chang... More Details >>
- No：22054
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Manual contactor on output side of drive unit

The low-voltage manual contactor is intended to prevent electric shock during inspection and maintenance of the drive unit.The MELIPM series motor is a synch... More Details >>
- No：21996
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
Brake unit selection

Since the FR-A540-0.75K has a brake transistor for resistor regenerative driving inside the inverter, you do not need to use BU. Just remove the jumper from ... More Details >>
- No：21992
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Difference between FR-AU01 and AU01A

The major changes from FR-AU01 to FR-AU01A include 1. Case material and 2. Lead wire terminal process method. The FR-AU01A has a backward compatibility with ... More Details >>
- No：21452
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Options
Coasting

When the inverter output shutoff signal MRS is turned on, the output is shut off immediately without regard to setting of Pr.250. More Details >>
- No：21423
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500

231-240 of Total 1353

Inquiries

page top