From before, the QCPU has been used and each setting does not make a difference internally. Thus, the selection was redu

Yes. It can be carried out like under the dancer feedback speed control.

It is available if the CC-Link option of the FR-A8NC is installed.

Vector control cannot be selected unless Pr.862 is set to 1. (Only the first motor is supported in the motor setting of

It is based on the maximum value that can be set for frequency. Specifically, it is 400 Hz.

The MM-BF and MM-CF are not compliant. The MM-GKR is compliant with the UL standard.

Both settings of Pr.83 and Pr.84 are enabled immediately. However, the output voltage is not changed because the value o

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

251-260 of Total 1368

prev 26 / 137page next

FR-A800-GF/FR-A800-E

Yes, they can. More Details >>
- No：20856
- Release Date：2018/08/22 16:24
- Category： FREQROL-A800
FR-SW3 CC-Link Seamless

From before, the QCPU has been used and each setting does not make a difference internally. Thus, the selection was reduced to the QCPU only. It can also be ... More Details >>
- No：20868
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Engineering Software
FR-A800-R2R

Yes. It can be carried out like under the dancer feedback speed control. More Details >>
- No：20885
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
FR-A800-E

It is available if the CC-Link option of the FR-A8NC is installed. More Details >>
- No：20894
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
FR Configurator2

Vector control cannot be selected unless Pr.862 is set to 1. (Only the first motor is supported in the motor setting of FR Configurator2.) More Details >>
- No：20908
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Engineering Software
FR-ASF

Yes. More Details >>
- No：20966
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options
FR-A800

It is based on the maximum value that can be set for frequency. Specifically, it is 400 Hz. More Details >>
- No：20979
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
Connection of the FR-HAL

Yes. More Details >>
- No：20985
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Options
UL standard

The MM-BF and MM-CF are not compliant. The MM-GKR is compliant with the UL standard. More Details >>
- No：21005
- Release Date：2018/08/22 16:25
- Category： Magnet motor drive
Vector control

Both settings of Pr.83 and Pr.84 are enabled immediately. However, the output voltage is not changed because the value of Pr.83 has little influence on Vecto... More Details >>
- No：21022
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800

251-260 of Total 1368

Inquiries

page top