The one-touch tuning does not require the response level setting also. Outlines of one-touch tuning and auto tuning are

1. The output frequency satisfies the "control specification/frequency precision" even when the power supply voltage cha

Select the high-duty brake resistor according to the inverter capacity.

Up to 30 m. (To avoid noise and voltage drop)

The frequency can be set to 65 Hz with the initial setting.Check if Pr.1 (Maximum frequency) is set to 60 Hz.

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note t

It seems that calibration for 20 mA current signal input is not correct.Use the calibration parameters "126" and "C7" to

When the programmable controller power is turned OFF while the inverter is in the PLC link operation mode, a communicati

The following causes are probable for persistent Err. display: 1. The terminals RES and SD are always short-circuited. 2

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

251-260 of Total 1354

prev 26 / 136page next

One-touch tuning

The one-touch tuning does not require the response level setting also. Outlines of one-touch tuning and auto tuning are as follows: One-touch tuning: You can... More Details >>
- No：23629
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4 , MELSERVO-JE
Speed change due to power supply voltage fluctuation

1. The output frequency satisfies the "control specification/frequency precision" even when the power supply voltage changes, but the output voltage cannot r... More Details >>
- No：22069
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Selection of high-duty brake resistor

Select the high-duty brake resistor according to the inverter capacity. More Details >>
- No：21953
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500 , FREQROL-E500
Frequency setting

Up to 30 m. (To avoid noise and voltage drop)　　 More Details >>
- No：21910
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

The frequency can be set to 65 Hz with the initial setting.Check if Pr.1 (Maximum frequency) is set to 60 Hz. More Details >>
- No：21858
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency setting

To accept the current signal, the terminals AU (current input selection) and SD must be short-circuited. Check it.Note that this terminal AU is not prepared ... More Details >>
- No：21799
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Frequency

It seems that calibration for 20 mA current signal input is not correct.Use the calibration parameters "126" and "C7" to calibrate the inverter.Perform calib... More Details >>
- No：21785
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Resetting inverter after restoring from power failure

When the programmable controller power is turned OFF while the inverter is in the PLC link operation mode, a communication error occurs and the inverter trip... More Details >>
- No：21417
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500
Dealing with Err.

The following causes are probable for persistent Err. display: 1. The terminals RES and SD are always short-circuited. 2. Operation panel contact or operatio... More Details >>
- No：21412
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Driving 200 V motor by 400 V inverter

Your suggested use is not recommended due to the following reasons: Output voltage of the 400 V inverter contains "micro surge". Usually this surge voltage i... More Details >>
- No：21403
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500

251-260 of Total 1354

Inquiries

page top