PHS does not cause the inverter to malfunction.On the contrary, if you use PHS near an inverter or motor, communication

Be sure to use the FR-E5P to mount the operation panel.This is because the board is bare on the back of the operation pa

If you ground the common terminals of the control circuit, it is connected with the inverter's earthing and the inverter

As an example, you can use an inverter to feed the cord at the constant speed under dancer control using a combination o

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the ou

As you mention, when the inverter is operated only with STF without inputting the speed command signal, the minimum freq

1. The braking torque can be considered 50% of the motor rated torque.2. The largest stress the DC injection brake gives

The phase detection terminal has been provided with units produced since December 1999. You can identify these units wit

The CAD data is found on the member's page of Mitsubishi Electric FA Global Website.

1. As the reactor (FR-HCL) is connected when connecting the FR-HC, do not connect the FR-BAL. 2. The noise filter can be

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

261-270 of Total 1354

prev 27 / 136page next

Influence by PHS

PHS does not cause the inverter to malfunction.On the contrary, if you use PHS near an inverter or motor, communication over PHS may become noisy or even get... More Details >>
- No：22018
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Operation panel

Be sure to use the FR-E5P to mount the operation panel.This is because the board is bare on the back of the operation panel and a dedicated connector is requ... More Details >>
- No：22030
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E500
Common terminals of control circuit

If you ground the common terminals of the control circuit, it is connected with the inverter's earthing and the inverter's noise may be input to the control ... More Details >>
- No：22037
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Winding control

As an example, you can use an inverter to feed the cord at the constant speed under dancer control using a combination of the deviation detector and deviatio... More Details >>
- No：22047
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Pulse train output of terminal FM

Under Advanced magnetic flux vector control, the output frequency varies due to slip compensation. This may cause the output frequency monitor value to chang... More Details >>
- No：22054
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Switching between high speed and low speed

As you mention, when the inverter is operated only with STF without inputting the speed command signal, the minimum frequency must be set to 10 Hz.However, a... More Details >>
- No：22078
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
DC injection brake

1. The braking torque can be considered 50% of the motor rated torque.2. The largest stress the DC injection brake gives to the motor is the motor heat gener... More Details >>
- No：22088
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Phase detection terminal

The phase detection terminal has been provided with units produced since December 1999. You can identify these units with the serial number "N9Z○○○○○○" or la... More Details >>
- No：22090
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Can you provide the CAD data?

The CAD data is found on the member's page of Mitsubishi Electric FA Global Website. More Details >>
- No：22091
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Others
Connection of options

1. As the reactor (FR-HCL) is connected when connecting the FR-HC, do not connect the FR-BAL. 2. The noise filter can be connected to the input side of the F... More Details >>
- No：22101
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options

261-270 of Total 1354

Inquiries

page top