The contact between the terminals RDY and SE is open collector output.Operation is:Normal: Non-conductiveFault: Conducti

Pr.133 can be written.Since the data code numbers of parameters are duplicate, target parameters are switched by link pa

The SF1258 has the terminal cover.Although the SF1259 to SF1263 do not have the terminal covers and their terminals are

You can set both the BCD code and binary code inputs within the range from 0 to 400 Hz.You can set the bias and gain in

As the inverter does not display the speed in m/min, let us explain using the speed display in r/min. In this case, set

Your suggestion is fine, but note that deceleration stop is naturally not available in case of an inverter error.In addi

Removal of the jumper between the terminals P1 and P is not necessary unless you are using the DC reactor.Set Pr.30 = "0

You can set reserved and invalid stations.The Instruction Manual instructs to set consecutive numbers because the master

Yes.You can issue operation (forward/reverse), frequency setting, parameter read/write, and operation monitor commands.

You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting t

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

281-290 of Total 1353

prev 29 / 136page next

Control wire of FR-HC RDY signal

The contact between the terminals RDY and SE is open collector output.Operation is:Normal: Non-conductiveFault: Conductive More Details >>
- No：22017
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Parameter writing via CC-Link

Pr.133 can be written.Since the data code numbers of parameters are duplicate, target parameters are switched by link parameter extended setting.You can acce... More Details >>
- No：21976
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500 , FREQROL-F500
EMC compliant filter terminal cover

The SF1258 has the terminal cover.Although the SF1259 to SF1263 do not have the terminal covers and their terminals are bare, rubber tubes to cover them are ... More Details >>
- No：21956
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
12-bit digital input

You can set both the BCD code and binary code inputs within the range from 0 to 400 Hz.You can set the bias and gain in 0.01 Hz units.For BCD input, when the... More Details >>
- No：21945
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500
I want to display the speed on an analog meter.

As the inverter does not display the speed in m/min, let us explain using the speed display in r/min. In this case, set Pr.52 to "6" (operation panel display... More Details >>
- No：21944
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Second deceleration time setting

Your suggestion is fine, but note that deceleration stop is naturally not available in case of an inverter error.In addition, considering regenerative power,... More Details >>
- No：21939
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Terminals P1 and P

Removal of the jumper between the terminals P1 and P is not necessary unless you are using the DC reactor.Set Pr.30 = "0" when using the brake unit.Since set... More Details >>
- No：21921
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link

You can set reserved and invalid stations.The Instruction Manual instructs to set consecutive numbers because the master regards an empty number as an error. More Details >>
- No：21905
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

Yes.You can issue operation (forward/reverse), frequency setting, parameter read/write, and operation monitor commands. More Details >>
- No：21899
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
CC-Link

You can select deceleration stop by setting Pr.502 (Stop mode selection at communication error). (Select from coasting to stop, deceleration to stop, and con... More Details >>
- No：21892
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P

281-290 of Total 1353

Inquiries

page top