It is not output in the JOG operation mode.

Since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of wa

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or

We can manufacture magnet motors with reduction gears.We have no catalog of them.Contact our sales representative for de

The standard product is not coated. The FR-A8AY-60 is the coated model.

Only the V/F control is related with Pr.56. The motor torque is calculated from the current value (not Pr.56) and motor

Yes, it is. However, it is not suitable for the low speed regenerative side. It is also recommended to use a dedicated c

When the second torque limit is used, the settings of Pr.816 and 817 are valid.

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated fo

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

21-30 of Total 1354

prev 3 / 136page next

PU signal

It is not output in the JOG operation mode. More Details >>
- No：21214
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-A5CN03

Since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of water. If you use the inverter (heat si... More Details >>
- No：21433
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Rotations per minute vary

It is considered that conditions including the power supply and noise change whether the parameter unit is connected or disconnected, influencing the analog ... More Details >>
- No：21454
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
Motor with reduction gears

We can manufacture magnet motors with reduction gears.We have no catalog of them.Contact our sales representative for details. More Details >>
- No：21982
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
FR-A8AY

The standard product is not coated. The FR-A8AY-60 is the coated model. More Details >>
- No：20872
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Plug-in Options
Load characteristics fault detection

Only the V/F control is related with Pr.56. The motor torque is calculated from the current value (not Pr.56) and motor constant. For the V/F control, it is ... More Details >>
- No：20893
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-F800
FR-A800-R2R

Yes, it is. However, it is not suitable for the low speed regenerative side. It is also recommended to use a dedicated control for winding/unwinding applicat... More Details >>
- No：20928
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL
Torque limit

When the second torque limit is used, the settings of Pr.816 and 817 are valid. More Details >>
- No：21218
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Inverter installation when using the FR-A7NCE

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated for 5 cm or more to pass the cable. More Details >>
- No：21227
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

21-30 of Total 1354

Inquiries

page top