Horizontal installation prevents heat release, resulting in a failure. Install the inverter vertically.

The operation cannot be manually switched to the commercial power supply operation at an inverter fault. The operation c

The length within 30 m is recommended. When the wiring length is long, signals may not be received accurately due to the

Yes, it can. For the capacity of 37K or more, use the included bracket for installation.

1. Pr.1 and 18 limit the output to 120 Hz. Use Pr.18 to change the maximum frequency. 2. If you want to output the binar

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you

"n" in the address RWwn indicates a value determined by the station number setting.

Normally, any of the PU, EXT, or NET LED turns ON.Check if the parameter unit FR-PU04/FR-PU07 or operation panel FR-PA07

Set Pr.52 (DU/PU main display data selection) to "5".This allows for displaying the setting frequency on the voltage mon

No problem.LEDs "PU" and "EXT" indicate that Pr.79 is set to "3"."MON" indicates that the operation status is monitored.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

291-300 of Total 1353

prev 30 / 136page next

Installation direction

Horizontal installation prevents heat release, resulting in a failure. Install the inverter vertically. More Details >>
- No：21286
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Electronic bypass function

The operation cannot be manually switched to the commercial power supply operation at an inverter fault. The operation can be automatically switched to the c... More Details >>
- No：21191
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Output signal

The length within 30 m is recommended. When the wiring length is long, signals may not be received accurately due to the increased inductance. More Details >>
- No：20995
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800 , FREQROL-F800 , FREQROL-E700 , FREQROL-D700
Combination of the FR-F800 and FR-A8TAT

Yes, it can. For the capacity of 37K or more, use the included bracket for installation. More Details >>
- No：20841
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options , FREQROL-F800
Digital input and maximum frequency

1. Pr.1 and 18 limit the output to 120 Hz. Use Pr.18 to change the maximum frequency. 2. If you want to output the binary input as is, setting Pr.304 = 1 (Bi... More Details >>
- No：22098
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A500
Calculation of acceleration/deceleration time

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you should consider a factor of 120% for ... More Details >>
- No：21965
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
CC-Link

"n" in the address RWwn indicates a value determined by the station number setting. More Details >>
- No：21867
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency setting

Normally, any of the PU, EXT, or NET LED turns ON.Check if the parameter unit FR-PU04/FR-PU07 or operation panel FR-PA07 is externally connected to the PU co... More Details >>
- No：21803
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Setting frequency

Set Pr.52 (DU/PU main display data selection) to "5".This allows for displaying the setting frequency on the voltage monitor.Then, switch to the monitor mode... More Details >>
- No：21784
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Operation panel LED

No problem.LEDs "PU" and "EXT" indicate that Pr.79 is set to "3"."MON" indicates that the operation status is monitored."RUN" indicates that the inverter is ... More Details >>
- No：21776
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ

291-300 of Total 1353

Inquiries

page top