It controls the charging current immediately after the power is ON. (as a resistor for charging current limit circuit)

The following reasons are possible. - The signal of Z phase does not exist. (It is not returned normally.) - The setting

The initial value of Pr.78 (Reverse rotation prevention selection) of the MD-CX522 is "1" (reverse rotation is disabled)

Refer to the inverter capacity.

Because the multi-speed terminal is disabled, it does not operate in multi-speed.

The writing from the parameter unit or operation panel is always ROM write regardless of the setting value of Pr.342.

When the brake sequence function is enabled, the RT signal is disabled and the stop-on-contact control cannot be perform

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring.

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated fo

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

321-330 of Total 1368

prev 33 / 137page next

FR-HC2

It controls the charging current immediately after the power is ON. (as a resistor for charging current limit circuit) More Details >>
- No：21150
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options
Orientation control

The following reasons are possible. - The signal of Z phase does not exist. (It is not returned normally.) - The setting of Pr.359 encoder rotation direction... More Details >>
- No：21162
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
MD-CX522

The initial value of Pr.78 (Reverse rotation prevention selection) of the MD-CX522 is "1" (reverse rotation is disabled). When performing forward rotation an... More Details >>
- No：21168
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Wiring length

Refer to the inverter capacity. More Details >>
- No：21200
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Leakage current

It is 1 mA as the 700 series. More Details >>
- No：21204
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Remote setting function

Because the multi-speed terminal is disabled, it does not operate in multi-speed. More Details >>
- No：21205
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
EEPROM writing with the communication option

The writing from the parameter unit or operation panel is always ROM write regardless of the setting value of Pr.342. More Details >>
- No：21206
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Stop-on-contact control

When the brake sequence function is enabled, the RT signal is disabled and the stop-on-contact control cannot be performed. More Details >>
- No：21209
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
LED blinking under encoder feedback control

The Z-phase signal may be connected to the A-phase or B-phase incorrectly. Check the wiring. More Details >>
- No：21220
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
Inverter installation when using the FR-A7NCE

Normally, the required space for A700 3.7K or lower is 1 cm. However, when using CC-Link IE, it needs to be separated for 5 cm or more to pass the cable. More Details >>
- No：21227
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

321-330 of Total 1368

Inquiries

page top