The surface temperature of approximately 70?C is OK.The following shows the MM-CF352 frame temperature for reference.(Ac

1. It is OK to open MC on the output side while the inverter is operating.2. It is OK to open the input side in case of

The key sheet fixed to the inverter is used for operation. Therefore, the conventional parameter unit cannot be used. (T

Position control is available under vector control with an encoder. Under PM sensorless vector control in combination wi

The FREQROL-F500 series has been already supported by the setup software released since February 2000.

Yes, you can set Pr.20 to 20 Hz.

The rated sensitivity current of the earth leakage circuit breaker can be calculated using the following equation. If th

The inverter (FR-A520-5.5K) itself generates approximately 310 W of heat. This is the amount generated under the inverte

Basically, torque control cannot be performed. Instead, control speed to adjust the winding torque. It is possible to us

Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

321-330 of Total 1353

prev 33 / 136page next

Motor heat generation

The surface temperature of approximately 70?C is OK.The following shows the MM-CF352 frame temperature for reference.(Actual temperature rise depends on how ... More Details >>
- No：21988
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
Power supply ON/OFF

1. It is OK to open MC on the output side while the inverter is operating.2. It is OK to open the input side in case of emergency stop. More Details >>
- No：21972
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Are conventional parameter units still available?

The key sheet fixed to the inverter is used for operation. Therefore, the conventional parameter unit cannot be used. (There is no connector to connect it.)O... More Details >>
- No：21597
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-U100
FR-A800

Position control is available under vector control with an encoder. Under PM sensorless vector control in combination with a MM-CF motor, simple positioning ... More Details >>
- No：21105
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800
Can I set the FR-F series parameters?

The FREQROL-F500 series has been already supported by the setup software released since February 2000. More Details >>
- No：22068
- Release Date：2018/08/22 16:30
- Category： Engineering Software
Frequency setting

Yes, you can set Pr.20 to 20 Hz. More Details >>
- No：21683
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Sensitivity current of earth leakage circuit breaker

The rated sensitivity current of the earth leakage circuit breaker can be calculated using the following equation. If the result is 30 mA or less, the NV-FA ... More Details >>
- No：21547
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Peripheral devices
Amount of heat

The inverter (FR-A520-5.5K) itself generates approximately 310 W of heat. This is the amount generated under the inverter rated current 100% load. Since the ... More Details >>
- No：21523
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A500
Simple torque control using stall prevention function

Basically, torque control cannot be performed. Instead, control speed to adjust the winding torque. It is possible to use the current limit function to preve... More Details >>
- No：21493
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Switching External operation, PU operation

Setting Pr.79 (Operation mode) to "6" sets the switchover mode. Pressing the "PU/EXT" key on the operation panel during External operation switches the mode ... More Details >>
- No：21289
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ

321-330 of Total 1353

Inquiries

page top