In the FR-A800/F800, the restriction on the wiring length of the shielded cable is eliminated. The wiring length is up t

It can be used in terms of the specifications. However, it is recommended to update the reactor and inverter at the same

Since the SF-PR is more efficient compared to the SF-JR, the resistance will decrease and the load current will increase

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intende

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4".

Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with

Change the setting in the PU operation mode.

Check if Pr.13 (Starting frequency) is set to higher than 10 Hz.Also check if a signal is input through the terminal MRS

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

341-350 of Total 1353

prev 35 / 136page next

Wiring length

In the FR-A800/F800, the restriction on the wiring length of the shielded cable is eliminated. The wiring length is up to 500 m as is the case with the unshi... More Details >>
- No：21089
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , FREQROL-F800
Use of the DC reactor

It can be used in terms of the specifications. However, it is recommended to update the reactor and inverter at the same time because the DC reactor was manu... More Details >>
- No：21017
- Release Date：2018/08/22 16:25
- Category： FREQROL-A800 , Inverters-FREQROL , FREQROL-F800 , FREQROL-A500 , FREQROL-F500
Replacement of the SF-JR with the SF-PR

Since the SF-PR is more efficient compared to the SF-JR, the resistance will decrease and the load current will increase. Check the following two points when... More Details >>
- No：20949
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Others
Motor retention at 0 Hz

The inverter does not have a function to limit the current at 0 Hz.Although it has the DC injection brake, it is intended to improve the braking capability b... More Details >>
- No：22002
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Brake unit selection

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply voltage 480 V- What resistance value... More Details >>
- No：21930
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
CC-Link

Use Pr.542 to set the station number and Pr.543 to set the baud rate.To set the baud rate to 10 Mbps, set Pr.543 to "4". More Details >>
- No：21839
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Frequency setting

Change Pr.161 (Frequency setting/key lock operation selection) to "1" (potentiometer mode).　　 More Details >>
- No：21792
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Minimum frequency

If any other frequency is not set, when the start signal is input, the inverter starts acceleration from 0.5 Hz set with Pr.13 (Starting frequency) up to 3 H... More Details >>
- No：21777
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
CC-Link station number setting

Change the setting in the PU operation mode.　　 More Details >>
- No：21747
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P
Parameter setting

Check if Pr.13 (Starting frequency) is set to higher than 10 Hz.Also check if a signal is input through the terminal MRS. More Details >>
- No：21722
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-F700PJ

341-350 of Total 1353

Inquiries

page top