The output signal across FM and SD is pulse output. The output frequency and number of pulses of the output signal acros

1. Wiring length between the inverter and the motor should be 500 m or less. For 0.75 kW or lower motors, the followi

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz w

If you connect two frequency setting potentiometers to the terminals 5 and 10, the permissible current of 10 mA is excee

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% to

I cannot tell whether or not you can drive the motor because the electrical specifications are not clear. It is conside

It is not recommended to install a contactor on the input side and connect the auxiliary contact to the terminal STF of

Refer to Section 2-45 and 2-46 of the FR-A series technical material.

Use the plug-in option dedicated for the FR-A100EXCELLENT. To avoid an incorrect installation, the connector position fo

The FR-E720S series and D720S series conform to the single-phase 200 V input specifications.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

361-370 of Total 1353

prev 37 / 136page next

Output specification between FM and SD

The output signal across FM and SD is pulse output. The output frequency and number of pulses of the output signal across FM and SD are proportional. However... More Details >>
- No：21384
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Wire length between inverter and motor

1. Wiring length between the inverter and the motor should be 500 m or less. For 0.75 kW or lower motors, the following relationship is true: Capacity... More Details >>
- No：21392
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Indication of potentiometer on operation panel

The potentiometer on the operation panel is initially calibrated so that the maximum indication is slightly over 60 Hz with the potentiometer turned to the m... More Details >>
- No：21427
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E500
Auxiliary input power supply

If you connect two frequency setting potentiometers to the terminals 5 and 10, the permissible current of 10 mA is exceeded, and you need to install 2 KΩ res... More Details >>
- No：21494
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Motor heat generation at low-speed operation

When using the FR-A540-3.7K in Advanced magnetic flux vector control, operating the motor continuously under the 100% torque at up to 3 Hz does not cause a h... More Details >>
- No：21496
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-A500
Driving German pole change motor by inverter

I cannot tell whether or not you can drive the motor because the electrical specifications are not clear. 　It is considered that you may drive the pole chang... More Details >>
- No：21518
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Installing contactor on input side

It is not recommended to install a contactor on the input side and connect the auxiliary contact to the terminal STF of the inverter for the following reason... More Details >>
- No：21533
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Amount of heat generated by inverter

Refer to Section 2-45 and 2-46 of the FR-A series technical material. More Details >>
- No：21554
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-A200
Compatibility of plug-in option

Use the plug-in option dedicated for the FR-A100EXCELLENT. To avoid an incorrect installation, the connector position for the plug-in option and the FR-A100E... More Details >>
- No：21632
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Plug-in Options , FREQROL-A100
Single-phase 200 V input

The FR-E720S series and D720S series conform to the single-phase 200 V input specifications. More Details >>
- No：21723
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700

361-370 of Total 1353

Inquiries

page top