With the FREQROL-U100 series, pressing and holding the [SET] switches to the current monitor.

You can short-circuit the terminals 10 and 2.If you are considering to perform operation at the maximum frequency, consi

Yes.Set Pr.19 (Base frequency voltage) to "200 V".200 V output will be obtained during 60 Hz operation.

Continuous 100% regenerative braking torque is available for the rated capacity of the high power factor converter. (The

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output cu

It is not completely recommended to use F700P because the starting torque at low speed of the hydraulic pump may be larg

The English version of SW3 can be installed with the product ID of FR Configurator2 if it is Ver.5.50 or later. Since Ve

Vector control cannot be selected unless Pr.862 is set to 1. Only the first motor is supported in the motor setting of F

The values are set to Pr.170 and 171 when the monitor value of cumulative power and actual operation time overflows. It

A current fluctuation may result in abnormal noise from the peripheral device or the flickering fluorescent light.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

371-380 of Total 1353

prev 38 / 136page next

Monitoring current value

With the FREQROL-U100 series, pressing and holding the [SET] switches to the current monitor. More Details >>
- No：22073
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-U100
Short-circuiting frequency setting terminals

You can short-circuit the terminals 10 and 2.If you are considering to perform operation at the maximum frequency, consider using the high-speed command RH o... More Details >>
- No：21951
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Motor specifications setting

Yes.Set Pr.19 (Base frequency voltage) to "200 V".200 V output will be obtained during 60 Hz operation. More Details >>
- No：21717
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Regenerative driving capability

Continuous 100% regenerative braking torque is available for the rated capacity of the high power factor converter. (The same braking ability of the FR-A201 ... More Details >>
- No：21563
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Connecting voltmeter to terminal AM

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output current should not exceed the permissib... More Details >>
- No：21464
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Selection

It is not completely recommended to use F700P because the starting torque at low speed of the hydraulic pump may be larger than that of the normal pump. Sele... More Details >>
- No：21126
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Others
FR Configurator2

The English version of SW3 can be installed with the product ID of FR Configurator2 if it is Ver.5.50 or later. Since Ver.5.50 or former does not have a prod... More Details >>
- No：20913
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Engineering Software
FR Configurator2

Vector control cannot be selected unless Pr.862 is set to 1. Only the first motor is supported in the motor setting of FR Configurator2. More Details >>
- No：20840
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Engineering Software , FREQROL-A800
Watt-hour meter clear and operation hour meter clear

The values are set to Pr.170 and 171 when the monitor value of cumulative power and actual operation time overflows. It does not affect the operation. Use it... More Details >>
- No：21197
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL
FR-HC2

A current fluctuation may result in abnormal noise from the peripheral device or the flickering fluorescent light. More Details >>
- No：21155
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , Options

371-380 of Total 1353

Inquiries

page top