MR Configurator2 has been improved in the following. ・The servo assistant function introduces the related functions fo

Before you change Pr.7 and Pr.8, you must switch to the PU operation mode. Switch to the PU operation mode and change th

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you

Rapid blinking of the RUN LED indicates that the frequency setting command has not been input or the output stop signal

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch whil

You cannot remove the key sheet from products with the key sheet attached as a standard other than the PU operation type

For the Instruction Manual "Applied", fill in the request sheet which is included in the last part of the Instruction Ma

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set

You can use the following two methods:1. Turn ON MRS at the same time when STF turns OFF.2. Set Pr.10 = 60 Hz, Pr.11 = 0

No load current for each power supply voltage is as follows:- Approximately 15.5 A for 200 VAC 60 Hz- Approximately 21.7

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

381-390 of Total 1353

prev 39 / 136page next

MR Configurator2

MR Configurator2 has been improved in the following. ・The servo assistant function introduces the related functions for each operation step to enable the f... More Details >>
- No：23658
- Release Date：2018/09/14 15:10
- Category： Servo Support Software
Changing parameters

Before you change Pr.7 and Pr.8, you must switch to the PU operation mode. Switch to the PU operation mode and change them. More Details >>
- No：21984
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-F500
Calculation of acceleration/deceleration time

As the inverter, you can basically use the equation below to calculate the acceleration/deceleration time.Note that you should consider a factor of 120% for ... More Details >>
- No：21965
- Release Date：2018/08/22 16:30
- Category： Magnet motor drive
Operation mode setting

Rapid blinking of the RUN LED indicates that the frequency setting command has not been input or the output stop signal has been input.Since Pr.79 is set to ... More Details >>
- No：21853
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Switching between external operation and NET operation

You can switch between external operation and NET operation by turning ON/OFF the terminal X66 (RM). You can switch while Pr.79 (Operation mode) is set to "6... More Details >>
- No：21688
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Key sheet

You cannot remove the key sheet from products with the key sheet attached as a standard other than the PU operation type. When using the parameter unit FR-PU... More Details >>
- No：21596
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , FREQROL-U100
Instruction manual

For the Instruction Manual "Applied", fill in the request sheet which is included in the last part of the Instruction Manual "Basic", and fax it to the speci... More Details >>
- No：21341
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Clearing the alarm history

By either of following methods: (MR-J4) 1. On MR Configurator2, select [Diagnosis] - [Alarm Display] - [Clear]. 2. Set alarm history clear of parameter to "... More Details >>
- No：23650
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4
How can I have the motor coast to stop?

You can use the following two methods:1. Turn ON MRS at the same time when STF turns OFF.2. Set Pr.10 = 60 Hz, Pr.11 = 0 sec, and Pr.12 = 0% (when the invert... More Details >>
- No：21967
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
No load current value of motor

No load current for each power supply voltage is as follows:- Approximately 15.5 A for 200 VAC 60 Hz- Approximately 21.7 A for 220 VAC 60 HzThe current is es... More Details >>
- No：21534
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Others

381-390 of Total 1353

Inquiries

page top