For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output cu

The harmonics generation device manufacturer application form must be created by the manufacturer and submitted by the c

The 0.75 kW inverter with the single-phase 100 V power supply can be manufactured and is actually commercialized as the

Be sure to use a high power factor converter with the capacity higher than the total capacity of the inverters connected

1. Select the circuit breaker and MC in accordance with the inverter type.2. Select the power factor improving reactor i

Use the RUN signal to turn ON and OFF the brake.Using the MRS (output shutoff) signal to turn ON the brake shuts off the

Basically, either is OK.Both orders are electrically identical, but "1" is recommended since it is preferable to place t

When connecting to the P/+, the current flows in the inrush circuit at the regenerative driving. This regenerative curre

Yes. When Pr.9 = 0, turning is performed with the inverter rated current. Always set the rated motor current.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

31-40 of Total 1368

prev 4 / 137page next

Priority of multi-speed setting and frequency setting signals

For frequency setting, multi-speed setting is prioritized over current input. Therefore, when the multi-speed signal is input, the inverter switch to multi-s... More Details >>
- No：21400
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Connecting voltmeter to terminal AM

You can connect them in parallel. Connect the voltmeters in parallel, paying attention to the following: - The output current should not exceed the permissib... More Details >>
- No：21464
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Harmonic Suppression Guidelines

The harmonics generation device manufacturer application form must be created by the manufacturer and submitted by the consumer when a device that contains a... More Details >>
- No：21507
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Single-phase 100 V series

The 0.75 kW inverter with the single-phase 100 V power supply can be manufactured and is actually commercialized as the FR-U100 series. Manufacturing of the ... More Details >>
- No：21509
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL
Inverter selection when multiple inverters are to be connected

Be sure to use a high power factor converter with the capacity higher than the total capacity of the inverters connected. (Note: One or more of the inverters... More Details >>
- No：21565
- Release Date：2018/08/22 16:28
- Category： Inverters-FREQROL , Options
Peripheral device selection

1. Select the circuit breaker and MC in accordance with the inverter type.2. Select the power factor improving reactor in accordance with the motor output. More Details >>
- No：21946
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
When controlling motor with brake by inverter

Use the RUN signal to turn ON and OFF the brake.Using the MRS (output shutoff) signal to turn ON the brake shuts off the inverter's output and reduces influe... More Details >>
- No：21960
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
AC reactor and line noise filter wiring

Basically, either is OK.Both orders are electrically identical, but "1" is recommended since it is preferable to place the line noise filter close to the inv... More Details >>
- No：21964
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
FR-A800/FR-F800

When connecting to the P/+, the current flows in the inrush circuit at the regenerative driving. This regenerative current may generate losses in the inrush ... More Details >>
- No：20815
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
FR-A800

Yes. When Pr.9 = 0, turning is performed with the inverter rated current. Always set the rated motor current. More Details >>
- No：20897
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL

31-40 of Total 1368

Inquiries

page top