The simple magnetic flux vector control is unavailable for the FR-F800. The advanced magnetic flux vector control is hig

Yes, it does, however, it does not acquire the certification of the BACnet association standard.

"OL" stands for "overload". Whenever current of 150% or more of the inverter rated current flows, "OL" is ON. If you con

Since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of wa

The possible causes of the error UVT are as follows.- Low power supply voltage - Insufficient power supply capacity - Da

Install the resistor between the terminals PC and OH.

When the DIP switch is changed to I, it does not operate normally because the internal resistance changes.

When the MR-J4-B is selected on the model selection screen at creating a new project, the multi-axis check box will be e

“off” is shown in th

Operation mode for manufacturer setting is enabled. For MR-J4-B, MR-J4W2-B and MR-J4W3-B, turning "ON (up)" all the cont

Data with different capacity can be imported. Data with different voltage or model cannot be imported.

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(86)

Geared Motors Parallel shaft type(23)
Geared Motors Right angle shaft type(25)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

421-430 of Total 1353

prev 43 / 136page next

Simple magnetic flux vector control

The simple magnetic flux vector control is unavailable for the FR-F800. The advanced magnetic flux vector control is higher-level function of the simple magn... More Details >>
- No：21058
- Release Date：2018/08/22 16:25
- Category： FREQROL-F800
FR-F800

Yes, it does, however, it does not acquire the certification of the BACnet association standard. More Details >>
- No：20863
- Release Date：2018/08/22 16:24
- Category： FREQROL-F800
Meaning of OL display

"OL" stands for "overload". Whenever current of 150% or more of the inverter rated current flows, "OL" is ON. If you continue operation with "OL" is displaye... More Details >>
- No：21449
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL , FREQROL-V200
FR-A5CN03

Since the heat sink and fan are not waterproof, you need to enclose them so that they are not exposed to the spray of water. If you use the inverter (heat si... More Details >>
- No：21433
- Release Date：2018/08/22 16:27
- Category： Inverters-FREQROL
Error "E.UVT" (undervoltage protection)

The possible causes of the error UVT are as follows.- Low power supply voltage - Insufficient power supply capacity - Damage or failure Check the power suppl... More Details >>
- No：21295
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-D700 , FREQROL-A700 , FREQROL-F700 , FREQROL-F700P , FREQROL-F700PJ
Vector control

Install the resistor between the terminals PC and OH. More Details >>
- No：21160
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL , FREQROL-A700
Terminal 2 input selector switch when the PTC thermistor is connected

When the DIP switch is changed to I, it does not operate normally because the internal resistance changes. More Details >>
- No：20901
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL
Specifying the axis in test operation of MR-J4W

When the MR-J4-B is selected on the model selection screen at creating a new project, the multi-axis check box will be enabled. Click the check box and selec... More Details >>
- No：23635
- Release Date：2018/09/14 15:10
- Category： Servo Support Software , MELSERVO-J4 , MELSERVO-J3
“off” is shown in the display.

Operation mode for manufacturer setting is enabled. For MR-J4-B, MR-J4W2-B and MR-J4W3-B, turning "ON (up)" all the control axis setting switches (SW2) enabl... More Details >>
- No：23625
- Release Date：2018/09/14 15:10
- Category： MELSERVO-J4
FR Configurator

Data with different capacity can be imported. Data with different voltage or model cannot be imported. More Details >>
- No：21196
- Release Date：2018/08/22 16:26
- Category： Inverters-FREQROL

421-430 of Total 1353

Inquiries

page top