If "1" is not shown on the frequency monitor, some of the parameters necessary for auto tuning may not be set correctly.

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply

Your suggestion is fine, but note that deceleration stop is naturally not available in case of an inverter error.In addi

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input

The brake unit and its resistor FR-S520-0.4K to 3.7K are available.Mitsubishi Electric FA Global Website also explains s

They are capable of a load of 5 VDC±5% and 10 mA.

The following benefits are provided when the FR-BLF is installed on the input side or output side.Choose the side to ins

The answers are as follows:- Effect of reactorAttaching a reactor improves the power factor and suppresses harmonics.The

It is considered that malfunction of the measurement device is due to noise. Check the noise propagation route since the

The following version or later is supported for Windows 8. MR Configurator2, 1.20W or later

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

431-440 of Total 1368

prev 44 / 137page next

Auto tuning

If "1" is not shown on the frequency monitor, some of the parameters necessary for auto tuning may not be set correctly.Set rated motor current of Pr.81 (Num... More Details >>
- No：21751
- Release Date：2018/08/22 16:29
- Category： Inverters-FREQROL , FREQROL-E700 , FREQROL-A700
Brake unit selection

1. The BU brake unit does not have the fault output.Multiple BU brake units can be connected in parallel.2. Power supply voltage 480 V- What resistance value... More Details >>
- No：21930
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Second deceleration time setting

Your suggestion is fine, but note that deceleration stop is naturally not available in case of an inverter error.In addition, considering regenerative power,... More Details >>
- No：21939
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL
Fault contact state when input side power supply is cut off

The NC contact does not open when the power supply is cut off whether the inverter is operating or ceased.When the input side power supply is cut off, the DC... More Details >>
- No：21958
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
Can I use a brake resistor with the FR-S500?

The brake unit and its resistor FR-S520-0.4K to 3.7K are available.Mitsubishi Electric FA Global Website also explains so.(Note that the GZG GRZG discharging... More Details >>
- No：21970
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-S500
Fault output contact rating

They are capable of a load of 5 VDC±5% and 10 mA. More Details >>
- No：21977
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , FREQROL-A500
Installation of FR-BLF

The following benefits are provided when the FR-BLF is installed on the input side or output side.Choose the side to install the FR-BLF considering these ben... More Details >>
- No：22026
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Installation of a reactor

The answers are as follows:- Effect of reactorAttaching a reactor improves the power factor and suppresses harmonics.The AC reactor improves the power factor... More Details >>
- No：22092
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Options
Influence on external measurement device

It is considered that malfunction of the measurement device is due to noise. Check the noise propagation route since the countermeasure depends on it. Some c... More Details >>
- No：22100
- Release Date：2018/08/22 16:30
- Category： Inverters-FREQROL , Others
Supported OS

The following version or later is supported for Windows 8. MR Configurator2, 1.20W or later More Details >>
- No：23633
- Release Date：2018/09/14 15:10
- Category： Servo Support Software

431-440 of Total 1368

Inquiries

page top