The resistor unit MT-BR5 manufactured in February 2016 or later has output terminal TH3 (NC contact) as a fault output t

The response delay time is 10 ms normally and 100 ms at startup.

It is possible when Pr.23 = 0 (Current limit at regenerative driving).

Perform the writing after turning ON the SOF, or after stopping the FR-HC2 by pressing the STOP button. Wire the RDY sig

Yes, it does, however, it does not acquire the certification of the BACnet association standard.

The FR-E7TR does not have the terminal for the SC and it cannot be used with the FR-E700-SC.

When the value is written to Pr.646 (Stored winding diameter), the stored value is used. When the value is not written,

If Pr.361 = 0, the second terminal can be used as the line speed command when X114 is ON, and as the frequency setting v

The tension PI gain can be adjusted automatically by performing the tension PI gain tuning.

For output signals, up to 10 points (RXn2 to RXB) can be assigned. It is possible if the number of the importing signal

FAQ

FAQAbout Products

Font Size
S
M
L

FAQ > Drive Products

FAQ

Inquiries

Keyword Search

You can search two or more words separated by a space.

 AND : Put a space between the words in a keyphrase.
 OR  : Add a vertical bar ( | ) between the words in a keyphrase.
 NOT : Add a minus sign ( - ) followed by the words that you would like to exclude.

Result Type

Text Search

Drive Products

Geared Motors(88)

Geared Motors Parallel shaft type(24)
Geared Motors Right angle shaft type(26)
S-PM Geared Motors Parallel shaft type(18)
S-PM Geared Motors Right angle shaft type(20)

FAQ within [ Drive Products ]

441-450 of Total 1368

prev 45 / 137page next

TH3 terminal of the MT-BR5

The resistor unit MT-BR5 manufactured in February 2016 or later has output terminal TH3 (NC contact) as a fault output terminal. More Details >>
- No：20816
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
FR-A8AY

The response delay time is 10 ms normally and 100 ms at startup. More Details >>
- No：20821
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Plug-in Options
FR-HC2

It is possible when Pr.23 = 0 (Current limit at regenerative driving). More Details >>
- No：20826
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
FR-HC2

Perform the writing after turning ON the SOF, or after stopping the FR-HC2 by pressing the STOP button. Wire the RDY signal so that the inverter stops when t... More Details >>
- No：20842
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , Options
FR-F800

Yes, it does, however, it does not acquire the certification of the BACnet association standard. More Details >>
- No：20863
- Release Date：2018/08/22 16:24
- Category： FREQROL-F800
FR-E700-SC

The FR-E7TR does not have the terminal for the SC and it cannot be used with the FR-E700-SC. More Details >>
- No：20865
- Release Date：2018/08/22 16:24
- Category： FREQROL-E700
FR-A800-R2R

When the value is written to Pr.646 (Stored winding diameter), the stored value is used. When the value is not written, the minimum or maximum winding diamet... More Details >>
- No：20887
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
FR-A800-R2R

If Pr.361 = 0, the second terminal can be used as the line speed command when X114 is ON, and as the frequency setting value when X114 is OFF. If Pr.361 = 3,... More Details >>
- No：20891
- Release Date：2018/08/22 16:24
- Category： Inverters-FREQROL , FREQROL-A800
FR-A800-R2R

The tension PI gain can be adjusted automatically by performing the tension PI gain tuning. More Details >>
- No：20923
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , FREQROL-A800
CC-Link

For output signals, up to 10 points (RXn2 to RXB) can be assigned. It is possible if the number of the importing signal points are within this range. More Details >>
- No：20943
- Release Date：2018/08/22 16:25
- Category： Inverters-FREQROL , Plug-in Options

441-450 of Total 1368

Inquiries

page top